ST72F264G ST Microelectronics, ST72F264G Datasheet - Page 27

• Manufacturer Part Number: ST72F264G
• Description: (ST72F260G - ST72F264G) 8-BIT MCU
• Manufacturer: ST Microelectronics

www.DataSheet4U.com
DataSheet
SYSTEM INTEGRITY MANAGEMENT (Cont’d)
6.4.5 Register Description
SYSTEM INTEGRITY (SI) CONTROL/STATUS REGISTER (SICSR)
Read /Write
Reset Value: 000x 000x (00h)
Bit 7 = Reserved, always read as 0.
Bit 6 = AVDIE Voltage Detector interrupt enable
This bit is set and cleared by software. It enables
an interrupt to be generated when the AVDF flag
changes (toggles). The pending interrupt informa-
tion is automatically cleared when software enters
the AVD interrupt routine.
0: AVD interrupt disabled
1: AVD interrupt enabled
Bit 5 = AVDF Voltage Detector flag
This read-only bit is set and cleared by hardware.
If the AVDIE bit is set, an interrupt request is gen-
erated when the AVDF bit changes value.
0: V
1: V
Bit 4 = LVDRF LVD reset flag
This bit indicates that the last Reset was generat-
ed by the LVD block. It is set by hardware (LVD re-
set) and cleared by software (writing zero). See
WDGRF flag description for more details. When
the LVD is disabled by OPTION BYTE, the LVDRF
bit value is undefined.
Bit 3 = Reserved, must be kept cleared.
Bit 2 = CSSIE Clock security syst
This bit enables the interrupt when a disturbance
is detected by the Clock Security System (CSSD
Address
7
0
(Hex.)
0025h
DD
DD
4
U
over V
under V
AVD
.com
IE
SICSR
Reset Value
AVD
IT+(AVD)
Register
F
IT-(AVD)
Label
LVD
RF
threshold
threshold
0
7
0
CSS
.
IE
interrupt enable
AVDIE
www.DataSheet4U.com
CSS
6
0
D
WDG
RF
0
AVDF
5
0
bit set). It is set and cleared by software.
0: Clock security system interrupt disabled
1: Clock security system interrupt enabled
When the CSS is disabled by OPTION BYTE, the
CSSIE bit has no effect.
Bit 1 = CSSD Clock security system detection
This bit indicates that the safe oscillator of the
Clock Security System block has been selected by
hardware due to a disturbance on the main clock
signal (f
reading the SICSR register when the original oscil-
lator recovers.
0: Safe oscillator is not active
1: Safe oscillator has been activated
When the CSS is disabled by OPTION BYTE, the
CSSD bit value is forced to 0.
Bit 0 = WDGRF Watchdog reset flag
This bit indicates that the last Reset was generat-
ed by the Watchdog peripheral. It is set by hard-
ware (watchdog reset) and cleared by software
(writing zero) or an LVD Reset (to ensure a stable
cleared state of the WDGRF flag when CPU
starts).
Combined with the LVDRF flag information, the
flag description is given by the following table.
Application Notes
The LVDRF flag is not cleared when another RE-
SET type occurs (external or watchdog), the
LVDRF flag remains set to keep trace of the origi-
nal failure. In this case, a watchdog reset can be
detected by software while an external reset can
not.
LVDRF
4
x
External RESET pin
RESET Sources
OSC
ST72260G, ST72262G, ST72264G
Watchdog
). It is set by hardware and cleared by
LVD
3
0
CSSIE
2
0
www.DataSheet
www.DataSheet
www.DataSheet
www.DataSheet4U
LVDRF
CSSD
1
0
0
0
1
WDGRF
WDGRF
27/171
0
x
X
0
1
4U
4U.com
4U
.com
.com
.com