LM3S1150-IQC50 Luminary Micro, Inc., LM3S1150-IQC50 Datasheet - Page 94

• Manufacturer Part Number: LM3S1150-IQC50
• Description: Microcontroller
• Manufacturer: Luminary Micro, Inc.

System Control
Run Mode Clock Gating Control Register 1 (RCGC1)
Base 0x400F.E000
Offset 0x104
Type R/W, reset 0x00000000
94
Reset
Reset
Type
Type
Bit/Field
31:27
23:20
26
25
24
19
RO
RO
31
15
0
0
Register 21: Run Mode Clock Gating Control Register 1 (RCGC1), offset 0x104
This register controls the clock gating logic. Each bit controls a clock enable for a given interface,
function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and
disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault.
The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are
disabled. It is the responsibility of software to enable the ports necessary for the application. Note
that these registers may contain more bits than there are interfaces, functions, or units to control.
This is to assure reasonable code compatibility with other family and future parts. RCGC1 is the
clock configuration register for running operation, SCGC1 for Sleep operation, and DCGC1 for
Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register
specifies that the system uses sleep modes.
reserved
RO
RO
30
14
0
0
reserved
reserved
TIMER3
COMP2
COMP1
COMP0
reserved
Name
RO
RO
29
13
0
0
Luminary Micro Confidential-Advance Product Information
I2C0
R/W
RO
28
12
0
0
RO
RO
Type
27
11
R/W
R/W
R/W
R/W
0
0
RO
RO
reserved
COMP2
R/W
RO
26
10
0
0
Reset
COMP1
0
0
0
0
0
0
R/W
RO
25
0
9
0
COMP0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
This bit controls the clock gating for analog comparator 2. If set, the unit
receives a clock and functions. Otherwise, the unit is unclocked and
disabled. If the unit is unclocked, reads or writes to the unit will generate
a bus fault.
This bit controls the clock gating for analog comparator 1. If set, the unit
receives a clock and functions. Otherwise, the unit is unclocked and
disabled. If the unit is unclocked, reads or writes to the unit will generate
a bus fault.
This bit controls the clock gating for analog comparator 0. If set, the unit
receives a clock and functions. Otherwise, the unit is unclocked and
disabled. If the unit is unclocked, reads or writes to the unit will generate
a bus fault.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
This bit controls the clock gating for General-Purpose Timer module 3.
If set, the unit receives a clock and functions. Otherwise, the unit is
unclocked and disabled. If the unit is unclocked, reads or writes to the
unit will generate a bus fault.
QEI0
R/W
R/W
24
0
8
0
RO
RO
23
0
7
0
reserved
RO
RO
22
0
6
0
reserved
SSI1
R/W
RO
21
0
5
0
SSI0
R/W
RO
20
0
4
0
reserved
TIMER3
R/W
RO
19
0
3
0
TIMER2
UART2
R/W
R/W
18
0
2
0
June 14, 2007
TIMER1
UART1
R/W
R/W
17
0
1
0
TIMER0
UART0
R/W
R/W
16
0
0
0