FDC37C665IR SMSC Corporation, FDC37C665IR Datasheet - Page 73
FDC37C665IR
Manufacturer Part Number
FDC37C665IR
Description
3/5 Volt Advanced High-Performance Multi-Mode Parallel Port Super I/O Floppy Disk Controller with Infranred Support
Manufacturer
SMSC Corporation
Datasheet
1.FDC37C665IR.pdf
(162 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FDC37C665IR
Manufacturer:
SMC
Quantity:
108
Part Number:
FDC37C665IR
Manufacturer:
SMC
Quantity:
20 000
- Current page: 73 of 162
- Download datasheet (563Kb)
In this mode, the Floppy Disk Control signals
are available on the parallel port pins. When
this mode is selected, the parallel port is not
available. There are two modes of operation,
PPFD1 and PPFD2.
selected in Configuration Register 4.
has only drive 1 on the parallel port pins; PPFD2
has drive 0 and 1 on the parallel port pins.
PPFD1:
PPFD2:
* If ECP is selected, then direct support for
drives 2 and 3 is not available. Drives 2 and 3
are available using external decoders.
When the PPFDC is selected the following pins
are set as follows:
1.
2.
3.
Drive 1 is on the Parallel port pins
Drive 2 is on the FDC pins*
Drive 3 is on the FDC pins*
Drive 1 is on the Parallel port pins
Drive 2 is on the FDC pins*
Drive 3 is on the FDC pins*
nDS2/PDIR (pin 98): not ECP = high-Z,
ECP = high
A10/nDS3 (pin 97): high-Z, A10 = to
internal logic.
nMTR2/nPDACK (pin 96): high-Z
Drive 0 is on the FDC pins
Drive 0 is on the Parallel port
pins
PARALLEL PORT FLOPPY DISK CONTROLLER
These modes can be
PPFD1
73
4.
5.
The following parallel port pins are read as
follows by a read of the parallel port register:
1.
2.
3.
The following FDC pins are all in the high
impedence state when the PPFDC is actually
selected by the drive select register:
1.
2.
The FDC signals are muxed onto the Parallel
Port pins as shown in Table 32.
nMTR3/PDRQ (pin 99): not ECP = high-Z,
ECP & dmaEn = 0, ECP & not dmaEn =
high-Z
PINTR: not active, this is hi-Z or Low
depending on settings.
Data Register (read) = last Data Register
(write)
Control Register are read as "cable not
connected" STROBE, AUTOFD and SLC =
0 and nINIT = 1;
Status Register reads: nBUSY = 0, PE = 0,
SLCT = 0, nACK = 1, nERR = 1.
nWDATA, DENSEL, nHDSEL, nWGATE,
nDIR,
nMTR1.
If PPFDx is selected, then the parallel port
can not be used as a parallel port until
"Normal" mode is selected.
nSTEP,
nDS1,
nDS0,
nMTRO,
Related parts for FDC37C665IR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: