cs4215 Cirrus Logic, Inc., cs4215 Datasheet - Page 25
![no-image](/images/manufacturer_photos/0/1/142/cirrus_logic__inc__sml.jpg)
cs4215
Manufacturer Part Number
cs4215
Description
16-bit Multimedia Audio Codec
Manufacturer
Cirrus Logic, Inc.
Datasheet
1.CS4215.pdf
(52 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
cs4215-KL
Manufacturer:
CRYSTAL
Quantity:
5 510
Part Number:
cs4215-KL
Manufacturer:
CRYSTAL
Quantity:
20 000
Part Number:
cs4215-KL ES
Manufacturer:
CIRRUS
Quantity:
20 000
Company:
Part Number:
cs4215-KLES
Manufacturer:
CRYSTRL
Quantity:
5 510
Company:
Part Number:
cs4215-KLES
Manufacturer:
NCR
Quantity:
5 510
Company:
Part Number:
cs4215KL
Manufacturer:
CRYSTRL
Quantity:
5 510
Company:
Part Number:
cs4215KL
Manufacturer:
ACTEL
Quantity:
5 510
Power Down Mode
Bringing the PDN pin high puts the CS4215 into
the power down mode. In this mode HEADC
and CMOUT will not supply current. Power
down will change all the control registers to the
reset state shown under each Control Time Slot
register. In the power down mode, the TSOUT
pin will follow the TSIN state with less than
10 ns delay.
After returning to normal operation from power
down, an offset calibration cycle must be exe-
cuted. Either bringing RESET low then high, or
updating the control registers, will cause an off-
set calibration cycle. In either case, a delay of
50 ms must occur after PDN goes low before
executing the offset calibration. This allows the
internal voltage reference time to settle.
DS76F2
0 is d iffe re n t fo r
(D A C d a ta = 0 )
e a ch d a ta
format
D A D
S D O U T
S D O U T
DD
SDIN
SDIN
D ig ita l-D igita l
L o o p b a ck
Figure 16. DD, DAD & ADA Loopback Paths
D ecod e
E n co d e
A/
E n co d e
D e co d e
A/
A/
A/
M o n ito r = 1 1 1 1
(Full M ute)
M o n ito r = 0
C S4215
C S4215
D /A
A /D
LOOPBACK TEST MODES
The CS4215 contains three loopback modes that
may be used to test the codec. Two of the loop-
back test modes are designed to allow the host to
perform a self-test on the CS4215. The third
mode allows laboratory testing using external
equipment.
Host Self-Test Loopback Modes
Since the CS4215 is a mixed-signal device, it is
equipped with an internal register that will en-
able the host to perform a two-tiered test on
power-up or as needed. The loopback test is en-
abled by setting the Enable Loopback bit, ENL,
in control register 4. The first tier of loopback is
a digital-digital loopback, DD, which is selected
by clearing the DAD bit in control register 4 (see
D /A
A/D
A tte n ua tio n
A tte n u a tio n
G a in
G a in
L o o p b a ck
A n a lo g -
D ig ita l-
D ig ita l
CS4215
L O U T
R O U T
(S till O p e ra te )
LIN
R IN
(D isco n n e cte d )
L O U T
R O U T
LIN
R IN
A D A
25