tda5225 Infineon Technologies Corporation, tda5225 Datasheet - Page 25
tda5225
Manufacturer Part Number
tda5225
Description
Enhanced Sensitivity Multi-channel Quad-conf Igurat Ion Receiver With Digital Slicer
Manufacturer
Infineon Technologies Corporation
Datasheet
1.TDA5225.pdf
(176 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 25 of 176
- Download datasheet (9Mb)
When defining a Multi-Channel system, the correct selection of channel spacing
is extremely important. A general rule is not possible, but following must be con-
sidered:
• If an additional SAW filter is used, all channels including their tolerances have to be
inside the SAW filter bandwidth.
• The distance between channels must be high enough, that no overlapping can occur.
Strong input signals may still appear as recognizable input signal in the neighboring
channel because of the limited suppression of IF Filters. Example: a typical 330kHz IF
filter has at 10.3 MHz ( 10.7 MHz - 0.4 MHz ) only 30 dB suppression. A -70 dBm input
signal appears like a -100 dBm signal, which is inside the receiver sensitivity. In critical
cases the use of two IF filters must be considered. See also
Receiver.
2.4.5.1
The divider chain consists of a band select divider 1/2/3, an I/Q-divider by 4 which
provides an orthogonal 1st local oscillator signal for the first image reject mixer with the
necessary high accuracy and a multi-modulus divider controlled by the Sigma-Delta
Modulator. With the band select divider, the wanted frequency band is selected. Divide
by 1 selects the 915 MHz and 868 MHz band, divide by 2 selects the 434 MHz band and
divide by 3 selects the 315 MHz band. The ISM band selection is done via bit group
BANDSEL in x_PLLINTC1 register.
2.4.5.2
The 3
LSB is always high, and is clocked by the XTAL oscillator. This determines the
achievable frequency resolution.
The Automatic Frequency Control Unit filters the actual frequency offset from the FSK
demodulator data and calculates the necessary correction of the divider factor to achieve
the nominal IF center frequency.
Data Sheet
rd
order Sigma-Delta Modulator (SDM) has a 22 bit wide input word, however the
PLL Dividers
Digital Modulator
25
Chapter 2.4.3 RF/IF
Functional Description
V1.0, 2010-02-19
TDA5225
Related parts for tda5225
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Antenna Switch Silicon Pin Diode
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Silicon Switching Diodes
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Single Igbt Driver Ic
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
5 Volt Standard Regulator
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Active Biased Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Small Signal Mosfet 20v?800v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Sipmos Small-signal Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v Small-signal-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
P-channel Mosfets Power-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Mosfet 20v?300v Power Transistor Power Mosfet
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Power Mosfets
Manufacturer:
Infineon Technologies Corporation
Datasheet: