sc16c654 NXP Semiconductors, sc16c654 Datasheet - Page 48
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
sc16c654
Manufacturer Part Number
sc16c654
Description
Quad Uart With 64-byte Fifo And Infrared Irda Encoder/decoder
Manufacturer
NXP Semiconductors
Datasheet
1.SC16C654.pdf
(52 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
sc16c654B
Manufacturer:
PHILIPS
Quantity:
132
Part Number:
sc16c654B1A68
Manufacturer:
PHI
Quantity:
20 000
Company:
Part Number:
sc16c654BIA68
Manufacturer:
NXP
Quantity:
152
Company:
Part Number:
sc16c654BIA68,512
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c654BIA68,518
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c654BIA68,529
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c654BIB64
Manufacturer:
VISHAY
Quantity:
100
Company:
Part Number:
sc16c654BIB64,128
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
sc16c654BIB64,151
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
sc16c654BIB64,151
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
sc16c654BIBM
Manufacturer:
NXP
Quantity:
291
Philips Semiconductors
12. Soldering
9397 750 11617
Product data
12.1 Introduction to soldering surface mount packages
12.2 Reflow soldering
12.3 Wave soldering
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages (document order number 9398 652 90011).
There is no soldering method that is ideal for all IC packages. Wave soldering can still
be used for certain surface mount ICs, but it is not suitable for fine pitch SMDs. In
these situations reflow soldering is recommended. In these situations reflow
soldering is recommended.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 270 C depending on solder
paste material. The top-surface temperature of the packages should preferably be
kept:
Moisture sensitivity precautions, as indicated on packing, must be respected at all
times.
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
•
•
•
below 220 C (SnPb process) or below 245 C (Pb-free process)
below 235 C (SnPb process) or below 260 C (Pb-free process) for packages with
a thickness < 2.5 mm and a volume < 350 mm
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
– for all BGA and SSOP-T packages
– for packages with a thickness
– for packages with a thickness < 2.5 mm and a volume
thick/large packages.
Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
Rev. 04 — 19 June 2003
2.5 mm
3
SC16C654/654D
so called small/thin packages.
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
350 mm
3
so called
48 of 52