S29GL-P_12 SPANSION [SPANSION], S29GL-P_12 Datasheet - Page 21
S29GL-P_12
Manufacturer Part Number
S29GL-P_12
Description
1 Gigabit, 512 Megabit, 256 Megabit and 128 Megabit 3.0 Volt-only Page Mode Flash Memory featuring 90 nm MirrorBit Process Technology
Manufacturer
SPANSION [SPANSION]
Datasheet
1.S29GL-P_12.pdf
(81 pages)
- Current page: 21 of 81
- Download datasheet (3Mb)
7.6
October 22, 2012 S29GL-P_00_A14
Autoselect
The Autoselect mode provides manufacturer ID, Device identification, and sector protection information,
through identifier codes output from the internal register (separate from the memory array) on DQ7-DQ0. This
mode is primarily intended for programming equipment to automatically match a device to be programmed
with its corresponding programming algorithm (see
in-system.
There are two methods to access autoselect codes. One uses the autoselect command, the other applies V
on address pin A9.
When using programming equipment, the autoselect mode requires V
Address pins must be as shown in
To access Autoselect mode without using high voltage on A9, the host system must issue the Autoselect
The Autoselect command sequence may be written to an address within a sector that is either in the read
The Autoselect command may not be written while the device is actively programming or erasing.
The system must write the reset command to return to the read mode (or erase-suspend-read mode if the
It is recommended that A9 apply V
See
When verifying sector protection, the sector address must appear on the appropriate highest order address
command.
or erase-suspend-read mode.
sector was previously in Erase Suspend).
that A9 apply from V
bits (see
been set as required, the programming equipment may then read the corresponding identifier code on
DQ15-DQ0. The Autoselect codes can also be accessed in-system through the command register.
Table 12.1 on page 69
Table 7.4
to
ID
Table
D a t a
to V
S29GL-P MirrorBit
IH
for command sequence details.
7.5). The remaining address bits are don't care. When all necessary bits have
/V
IL
Table
S h e e t
before power-down the V
ID
after power-up sequence is completed. In addition, it is recommended
7.2.
®
Flash Family
Table
7.3). The Autoselect codes can also be accessed
CC
/V
IO
.
ID
(11.5 V to 12.5 V) on address pin A9.
21
ID
Related parts for S29GL-P_12
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
3.0 Volt-only Page Mode Flash Memory Featuring 90 Nm Mirrorbit Process Technology
Manufacturer:
Meet Spansion Inc.
Datasheet:
Part Number:
Description:
S29GL-A MirrorBit Flash Family
Manufacturer:
SPANSION [SPANSION]
Datasheet:
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
TS 48/CIVIL/1-BIT ECC, X8 I/O AND 3V VCC SPANSION SLC NAND
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
MBM29F400TC-70PFTNSPANSION [FLASH MEMORY CMOS 4M (512K x 8/256K x 16) BIT]
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
AM29F010B70JI1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016D70BAI02016 MEGABIT CMOS 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI01016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
S29AL016M90FAI02016 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet:
Part Number:
Description:
Manufacturer:
SPANSION
Datasheet: