PCF88332DA PHILIPS [NXP Semiconductors], PCF88332DA Datasheet - Page 13
![no-image](/images/no-image-200.jpg)
PCF88332DA
Manufacturer Part Number
PCF88332DA
Description
STN RGB - 132 X 132 X 3 driver
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.PCF88332DA.pdf
(112 pages)
- Current page: 13 of 112
- Download datasheet (464Kb)
Philips Semiconductors
6.2
6.2.1
No operation (NOP) has no effect on internal data or settings. However, it can be used to terminate data transfer (read
and write).
Table 3 No operation command bits
6.2.2
The PCF8833 has a hardware and a software reset. After
power-up a hardware reset (pin RES) must be applied; see
Fig.50. The hardware and software resets give the same
results. After a reset, the chip has the following state:
Table 4 Reset state after hardware and software reset
2003 Feb 14
Sleep_IN
INVOFF
BSTRON
DISPON
TEOFF
IDMOFF
NORON
V
MY
RGB
MX
LAO
BRS
TRS
FINV
DOR
TCDFE
TCVOPE
EC
All LCD outputs are set to V
RAM data unchanged
Power-down mode (Sleep_IN)
Command register set to default states; see Table 4
Interface pins are set to inputs.
STN RGB - 132
COMMAND
D/C
0
Function set
N
R
O OPERATION
ESET
7
0
PCF8833 is in Sleep_IN mode (booster and display are switched off)
display inversion is off
when Sleep_OUT is active; booster is switched on
when Sleep_OUT is active; display is turned on
tearing effect line pulse is turned off
Idle mode is turned off (4 kbyte colour mode, not 8-colour mode)
Normal mode is active, not Scroll or Partial mode
RAM write in X direction
no mirror Y
colour order is RGB
no mirror X
line address order (top to bottom)
bottom rows are not mirrored; note 1
top rows are not mirrored; note 1
super frame inversion is on
normal data order
DF temperature compensation switched on
VOP temperature compensation switched on
internal oscillator
6
0
132
SS
(display off)
3 driver
5
0
DESCRIPTION
4
0
13
After a reset, care must be taken with respect to the reset
timing constraints (see Fig.50) when the PCF8833 is
powered-up. The power-up must be done by sending the
Sleep_OUT command.
After a power-up the display RAM content is undefined.
Neither a hardware reset nor a software reset changes the
data that is stored in the display RAM. Sending display
data must stop 160 ns before issuing a hardware reset,
otherwise the last word written to the display RAM may be
corrupted. The row and column outputs are tied to V
with a reset because power-down (Sleep_IN) is in the
reset state.
3
0
2
0
1
0
Objective specification
0
0
0
0
0
0
0
1
0
1
1
0
RESET STATE
0
0
PCF8833
DEFAULT
00H
SS1
Related parts for PCF88332DA
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ICM7555IN](/images/no-image3.png)
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C554BIB64](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![BZW03-C100](/images/no-image3.png)
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![P51XAG30KFA](/images/no-image3.png)
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C2550B_07](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C650BIBS](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C652BIBS](/images/no-image3.png)
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16C654BIB64](/images/no-image3.png)
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC16IS740IPW](/images/no-image3.png)
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![SC18IM700IPW](/images/no-image3.png)
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![TFA9812HN](/images/no-image3.png)
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![TFA9881_1104](/images/no-image3.png)
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![PC88](/images/no-image3.png)
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
![TH0912250](/images/manufacturer_photos/0/5/522/philips_semiconductors_tmb.jpg)
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
![TH0912251](/images/manufacturer_photos/0/5/522/philips_semiconductors_tmb.jpg)
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors