SAA7108AE PHILIPS [NXP Semiconductors], SAA7108AE Datasheet - Page 49
SAA7108AE
Manufacturer Part Number
SAA7108AE
Description
HD-CODEC
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.SAA7108AE.pdf
(197 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SAA7108AE/G
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
SAA7108AE/V1
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Part Number:
SAA7108AE/V1/G
Manufacturer:
NXP/恩智浦
Quantity:
20 000
- Current page: 49 of 197
- Download datasheet (937Kb)
Philips Semiconductors
9.1.4
The prefiltered luminance signal is fed to the
synchronization stage. Its bandwidth is further reduced to
1 MHz by a low-pass filter. The sync pulses are sliced and
fed to the phase detectors where they are compared with
the sub-divided clock frequency. The resulting output
signal is applied to the loop filter to accumulate all phase
deviations. Internal signals (e.g. HCL and HSY) are
generated in accordance with analog front-end
requirements. The loop filter signal drives an oscillator to
generate the line frequency control signal (LFCO);
see Fig.28.
The detection of ‘pseudo syncs’ as part of the Macrovision
copy protection standard is also done within the
synchronization circuit.
The result is reported as flag COPRO within the decoder
status byte at subaddress 1FH.
9.1.5
The internal CGC generates all clock signals required for
the video input processor.
9.1.6
A missing clock, insufficient digital or analog V
are forced to 3-state (see Fig.29). The indicator output RESd is LOW for approximately 128 LLC after the internal reset
and can be applied to reset other circuits of the digital TV system.
It is possible to force a reset by pulling the Chip Enable (CE) to ground. After the rising edge of CE and sufficient power
supply voltage, the outputs LLC, LLC2 and SDAd return from 3-state to active, while the other signals have to be
activated via programming.
2004 Jun 29
HD-CODEC
S
C
P
YNCHRONIZATION
OWER
LOCK GENERATION CIRCUIT
LFCO
-
ON RESET AND
BAND PASS
FC = LLC/4
CE
Fig.28 Block diagram of the clock generation circuit.
INPUT
DETECTION
CROSS
ZERO
DDAd
supply voltages (below 2.7 V) will start the reset sequence; all outputs
DETECTION
PHASE
49
The internal signal LFCO is a digital-to-analog converted
signal provided by the horizontal PLL. It is a multiple of the
line frequency:
The LFCO signal is multiplied internally by a factor of
2 and 4 in the PLL circuit (including phase detector, loop
filtering, VCO and frequency divider) to obtain the output
clock signals. The rectangular output clocks have a 50 %
duty cycle.
Table 16 Decoder clock frequencies
XTAL
LLC
LLC2
LLC4 (internal)
LLC8 (virtual)
6.75 MHz = 429
6.75 MHz = 432
CLOCK
DIVIDER
FILTER
LOOP
1/2
SAA7108AE; SAA7109AE
f
f
H
H
(50 Hz), or
(60 Hz).
OSCILLATOR
DIVIDER
1/2
MHB330
FREQUENCY (MHz)
24.576 or 32.110
Product specification
3.375
13.5
6.75
LLC
LLC2
27
Related parts for SAA7108AE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors