LAN9218-MT-E2 SMSC [SMSC Corporation], LAN9218-MT-E2 Datasheet - Page 36
![no-image](/images/no-image-200.jpg)
LAN9218-MT-E2
Manufacturer Part Number
LAN9218-MT-E2
Description
High-Performance Single- Chip 10/100 Ethernet Controller with HP Auto-MDIX
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.LAN9218-MT-E2.pdf
(130 pages)
- Current page: 36 of 130
- Download datasheet (2Mb)
Revision 1.5 (07-18-06)
3.11
3.11.1
3.11.2
3.11.2.1
The LAN9218 supports power-down modes to allow applications to minimize power consumption. The
following sections describe these modes.
System Description
Power is reduced to various modules by disabling the clocks as outlined in Table 3.9, “Power
Management States,” on page 37. All configuration data is saved when in either of the twolow power
states. Register contents are not affected unless specifically indicated in the register description.
Functional Description
There is one normal operating power state, D0 and there are two power saving states: D1, and D2.
Upon entry into either of the two power saving states, only the PMT_CTRL register is accessible for
read operations. In either of the power saving states the READY bit in the PMT_CTRL register will be
cleared. Reads of any other addresses are forbidden until the READY bit is set. All writes, with the
exception of the wakeup write to BYTE_TEST, are also forbidden until the READY bit is set. Only when
in the D0 (Normal) state, when the READY bit is set, can the rest of the device be accessed.
Note 3.3
In system configurations where the PME signal is shared amongst multiple devices, the WUPS field
within the PMT_CTRL register can be read to determine which LAN9218 device is driving the PME
signal.
When the LAN9218 is in a power saving state (D1 or D2), a write cycle to the BYTE_TEST register
will return the LAN9218 to the D0 state.
Components,” on page 126
page
Note 3.4
D1 Sleep
Power consumption is reduced in this state by disabling clocks to portions of the internal logic as
shown in
operational. This state is entered when the host writes a '01' to the PM_MODE bits in the Power
Management (PMT_CTRL) register. The READY bit in PMT_CTRL is cleared when entering the D1
state.
Wake-up frame and Magic Packet detection are automatically enabled in the D1 state. If properly
enabled via the WOL_EN and PME_EN bits, the LAN9218 will assert the PME hardware signal upon
the detection of the wake-up frame or magic packet. The LAN9218 can also assert the host interrupt
(IRQ) on detection of a wake-up frame or magic packet. Upon detection, the WUPS field in PMT_CTRL
will be set to a 10b.
Note 3.5
Note 3.6
A write to the BYTE_TEST register, regardless of whether a wake-up frame or Magic Packet was
detected, will return LAN9218 to the D0 state and will reset the PM_MODE field to the D0 state. As
Power Management
126, shows the power consumption values for each power state.
Table
The LAN9218 must always be read at least once after power-up, reset, or upon return from
a power-saving state, otherwise write operations will not function.
When the LAN9218 is in a power saving state, a write of any data to the BYTE_TEST
register will wake-up the device. DO NOT PERFORM WRITES TO OTHER
ADDRRESSES while the READY bit in the PMT_CTRL register is cleared.
The PME interrupt status bit (PME_INT) in the INT_STS register is set regardless of the
setting of PME_EN.
Wake-up frame and Magic Packet detection is automatically enabled when entering the D1
state. For wake-up frame detection, the wake-up frame filter must be programmed before
entering the D1 state (see
the host interrupt and PME signal must be enabled prior to entering the D1 state.
3.9. In this mode the clock to the internal PHY and portions of the MAC are still
and
Table 7.2, “Power Consumption Device and System Components,” on
DATASHEET
Section 3.5, "Wake-up Frame Detection," on page
36
Table 7.2, “Power Consumption Device and System
High-Performance Single-Chip 10/100 Ethernet Controller with HP Auto-MDIX
SMSC LAN9218
25). If used,
Datasheet
Related parts for LAN9218-MT-E2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN83C183-JD](/images/no-image3.png)
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N769TQFP](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47M102S-MC](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N267-MN](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![USB20H04-JD](/images/no-image3.png)
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37M602](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37B777](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37C672](/images/no-image3.png)
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
![COM90C66LJP](/images/no-image3.png)
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869TQFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![USB97C100QFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N227-MN](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![LAN91C94](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: