DSPIC30F6010A MICROCHIP [Microchip Technology], DSPIC30F6010A Datasheet - Page 102
![no-image](/images/no-image-200.jpg)
DSPIC30F6010A
Manufacturer Part Number
DSPIC30F6010A
Description
High-Performance, 16-bit Digital Signal Controllers
Manufacturer
MICROCHIP [Microchip Technology]
Datasheet
1.DSPIC30F6010A.pdf
(236 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F6010A-20E/PF
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
DSPIC30F6010A-20E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F6010A-20E/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
DSPIC30F6010A-20I/PF
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
DSPIC30F6010A-20I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F6010A-20I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
DSPIC30F6010A-30I/
Manufacturer:
TI
Quantity:
7 880
Company:
Part Number:
DSPIC30F6010A-30I/PF
Manufacturer:
AD
Quantity:
2 100
Company:
Part Number:
DSPIC30F6010A-30I/PF
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
DSPIC30F6010A-30I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F6010A-30I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Complementary mode by default upon a device Reset.
dsPIC30F6010A/6015
15.6
In the Complementary mode of operation, each pair of
PWM outputs is obtained by a complementary PWM
signal. A dead time may be optionally inserted during
device switching, when both outputs are inactive for a
short period (Refer to
Generators”).
In Complementary mode, the duty cycle comparison
units are assigned to the PWM outputs as follows:
• PDC1 register controls PWM1H/PWM1L outputs
• PDC2 register controls PWM2H/PWM2L outputs
• PDC3 register controls PWM3H/PWM3L outputs
• PDC4 register controls PWM4H/PWM4L outputs
The Complementary mode is selected for each PWM
I/O pin pair by clearing the appropriate PMODx bit in the
PWMCON1 SFR. The PWM I/O pins are set to
15.7
Dead-time generation may be provided when any of
the PWM I/O pin pairs are operating in the
Complementary Output mode. The PWM outputs use
Push-Pull drive circuits. Due to the inability of the
power output devices to switch instantaneously, some
amount of time must be provided between the turn off
event of one PWM output in a complementary pair and
the turn on event of the other transistor.
The PWM module allows two different dead times to be
programmed. These two dead times may be used in
one of two methods described below to increase user
flexibility:
• The PWM output signals can be optimized for
• The two dead times can be assigned to individual
15.7.1
Each complementary output pair for the PWM module
has a 6-bit down counter that is used to produce the
dead-time insertion. As shown in
dead-time unit has a rising and falling edge detector
connected to the duty cycle comparison output.
DS70150E-page 102
different turn off times in the high side and low
side transistors in a complementary pair of tran-
sistors. The first dead time is inserted between
the turn off event of the lower transistor of the
complementary pair and the turn on event of the
upper transistor. The second dead time is inserted
between the turn off event of the upper transistor
and the turn on event of the lower transistor.
PWM I/O pin pairs. This Operating mode allows
the PWM module to drive different transistor/load
combinations with each complementary PWM I/O
pin pair.
Complementary PWM Operation
Dead-Time Generators
DEAD-TIME GENERATORS
Section 15.7 “Dead-Time
Figure
15-4, each
15.7.2
The DTCON2 SFR contains control bits that allow the
dead times to be assigned to each of the complemen-
tary outputs.
each dead-time selection control bit.
TABLE 15-1:
15.7.3
The amount of dead time provided by each dead-time
unit is selected by specifying the input clock prescaler
value and a 6-bit unsigned value. The amount of dead
time provided by each unit may be set independently.
Four input clock prescaler selections have been pro-
vided to allow a suitable range of dead times, based on
the device operating frequency. The clock prescaler
option may be selected independently for each of the
two dead-time values. The dead-time clock prescaler
values are selected using the DTAPS<1:0> and
DTBPS<1:0> control bits in the DTCON1 SFR. One of
four clock prescaler options (T
may be selected for each of the dead-time values.
After the prescaler values are selected, the dead time
for each unit is adjusted by loading two 6-bit unsigned
values into the DTCON1 SFR.
The dead-time unit prescalers are cleared on the
following events:
• On a load of the down timer due to a duty cycle
• On a write to the DTCON1 or DTCON2 registers.
• On any device Reset.
DTS1A PWM1L/PWM1H active edge dead time.
DTS1I
DTS2A PWM2L/PWM2H active edge dead time.
DTS2I
DTS3A PWM3L/PWM3H active edge dead time.
DTS3I
DTS4A PWM4L/PWM4H active edge dead time.
DTS4I
comparison edge event.
Note:
Bit
PWM1L/PWM1H inactive edge dead time.
PWM2L/PWM2H inactive edge dead time.
PWM3L/PWM3H inactive edge dead time.
PWM4L/PWM4H inactive edge dead time.
DEAD-TIME ASSIGNMENT
DEAD-TIME RANGES
The user should not modify the DTCON1
or DTCON2 values while the PWM mod-
ule is operating (PTEN = 1). Unexpected
results may occur.
Table 15-1
DEAD-TIME SELECTION BITS
© 2011 Microchip Technology Inc.
summarizes the function of
Selects
CY
, 2 T
CY
, 4 T
CY
or 8 T
CY
)