MT90222 ZARLINK [Zarlink Semiconductor Inc], MT90222 Datasheet - Page 61
![no-image](/images/no-image-200.jpg)
MT90222
Manufacturer Part Number
MT90222
Description
4/8/16 Port IMA/TC PHY Device
Manufacturer
ZARLINK [Zarlink Semiconductor Inc]
Datasheet
1.MT90222.pdf
(155 pages)
- Current page: 61 of 155
- Download datasheet (920Kb)
4.8.4
The MT90222/3/4 implements circuitry to determine whether or not a selected clock signal is active. This feature is
used to ensure a clock is operational before using it as a source for one or more transmit links. A read of the TXCK
Status (0x0630), RXCK Status (0x0631) or REFCK Status (0x0632) register indicates a faulty clock if a bit is ’1’.
A value of ’0’ for these bits means that activity was observed on this clock. This circuitry does not measure the
frequency of a clock signal, it only detects activity on the TXCK, RXCK and REFCK signals.
4.8.5
The clock selection circuitry selects the desired clock signal and ensures a smooth, glitch free, transition between
the current clock source and the new clock source. Clock source activity can be verified using the TXCK Status
(0x0630), RXCK Status (0x0631) or REFCK Status (0x0632) registers.
5.0
The MT90222/3/4 supports the UTOPIA L1 and L2 Mode, 8 or 16 bit wide bus, with odd/even parity, for cell level
handshake only.In 8-bit UTOPIA mode maximum supported clock is up to 52 MHz and in 16-bit mode it is 33 MHz.
Each port can be assigned an address ranging from 0 to 30. The address value of 31 is reserved and should not be
used.
The TX and RX paths of each IMA Group and each link in TC has its own PHY address. These PHY addresses are
defined in the UTOPIA Input Link Address (0x0040-0x0047) registers, UTOPIA Input Group Address
(0x0048-0x004B) registers, UTOPIA Output Link Address (0x000-0x0007) registers, and the UTOPIA Output
Group Address (0x0008-0x000B) registers. The UTOPIA Input LINK PHY Enable (0x0050) and the UTOPIA
Output Link PHY Enable (0x0010) registers are used to enable the PHY Address of the links in TC mode. The
UTOPIA Input Group PHY Enable (0x0051) register and the UTOPIA Output Group PHY Enable (0x0011)
registers are used to enable the PHY Address of the IMA Groups.
The MT90222/3/4 UTOPIA port uses handshaking signals to process data streams. The start of a cell (SOC) is
marked by the UTOPIA SOC sync signal. This signal is active during the transfer of the first byte/first word of a cell.
The 52 bytes/26 words that follow the arrival of the first byte/first word of a cell are interpreted as belonging to the
same cell and are stored accordingly.
The Cell Available status line (Clav) is used to communicate to the ATM controller whether the MT90222/3/4 has
space for a cell in the PHY address that was polled in the previous cycle. Whenever there is space for a cell in the
TX direction or a cell ready in the RX direction, the TXClav and/or RXClav signal will be driven High. If there is no
space in Tx direction and/or no cell is ready in Rx direction, the TxClav and/or RxCLav will be kept low. When the
address does not correspond to any enabled PHY address inside the MT90222/3/4, the TXClav and RXClav signal
are set to High impedance mode. The use of an external pull-down may be required for the proper operation of the
Utopia bus in MPHY mode.
Note that the transmit or receive Utopia clock frequencies do not have to be synchronized with the system clock but
their frequencies cannot exceed the system clock frequency.
Important Note: The MT90224/3/2 doesn’t support the back-to-back mode on Rx side (ATM output port).
Depending on which ATM controller the MT90222/3/4 interfaces to, there might be interoperability issues that affect
the receive side communication. For details, please refer to Technical Note ZLAN-88: UTOPIA Interface between
MT90224/3/2 and Specific ATM Controllers.
5.1
The UTOPIA interface input clock TxClk is independent of the system clock. The UTOPIA TxClk can be up to 52
MHz for 8-bit mode and up to 33 MHz for 16-bit mode. The incoming cell is stored directly in the internal TX Cell
RAM where the TX UTOPIA FIFOs are implemented.
ATM Input Port
UTOPIA Interface Operation
Verification of Clock Activity
Clock Selection
Zarlink Semiconductor Inc.
MT90222/3/4
61
Data Sheet
Related parts for MT90222
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![SL1430](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_tmb.jpg)
Part Number:
Description:
Zarlink Semiconductor Inc [TV IF PREAMPLIFIER]
Manufacturer:
Zarlink Semiconductor
Datasheet:
![MT312C](/images/no-image3.png)
Part Number:
Description:
Satellite Channel Decoder
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![MSC60028/IG/DP2S](/images/no-image3.png)
Part Number:
Description:
Power Factor Controller
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![P10C68-](/images/no-image3.png)
Part Number:
Description:
CMOS/SNOS NVSRAM HIGH PERFORMANCE 8 K x 8 NON-VOLATILE STATIC RAM
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2009KG](/images/no-image3.png)
Part Number:
Description:
Dual stage IF amplifier for cable tuners
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2101C](/images/no-image3.png)
Part Number:
Description:
Synthesized Broadband Converter with Programmable Power
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2150KG](/images/no-image3.png)
Part Number:
Description:
Cable Tuner Front End LNA with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2150LH2S](/images/no-image3.png)
Part Number:
Description:
Front End Power Splitter with AGC
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2524HP](/images/no-image3.png)
Part Number:
Description:
1.3GHz Dual Wideband Logarithmic Amplifier
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL2610IG](/images/no-image3.png)
Part Number:
Description:
Wide Dynamic Range Image Reject MOPLL
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL1451NADP](/images/no-image3.png)
Part Number:
Description:
WIDEBAND PLL FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL1452NAMP](/images/no-image3.png)
Part Number:
Description:
WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL161](/images/no-image3.png)
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL1613CDP](/images/no-image3.png)
Part Number:
Description:
WIDEBAND LOG IF STRIP AMPLIFIER
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet:
![SL1640](/images/no-image3.png)
Part Number:
Description:
THIS DOCUMENT IS FOR MAINTENANCE PURPOSES ONLY AND IS NOT RECOMMENDED FOR NEW DESIGNS
Manufacturer:
ZARLINK [Zarlink Semiconductor Inc]
Datasheet: