EN29GL128H-70BAIP EON [Eon Silicon Solution Inc.], EN29GL128H-70BAIP Datasheet - Page 54

• Manufacturer Part Number: EN29GL128H-70BAIP
• Description: 128 Megabit (16384K x 8-bit / 8192K x 16-bit) Flash Memory Page mode Flash Memory, CMOS 3.0 Volt-only
• Manufacturer: EON [Eon Silicon Solution Inc.]

Revisions List
This Data Sheet may be revised by subsequent versions
or modifications due to changes in technical specifications.
Revision No
A
B
C
D
E
F
G
H
Description
Preliminary
1.Add Sector for write protect selection in Ordering information
2.Modify PPB sector group in table 7 and Figure 7.
3. Modify sector erase descirption and Figure 6.
1. Add internal pull-up description for WP# pin in Table1 on Page 4
2. Add WP#/ACC, VIO pin in Figure3 on Page 4
3. Modify tOE from 30ns to 25ns in Table 17 on Page 40 and Page 5
4. Add Secured Silicon Sector Entry/Exit command in Table13
5. Modify typo from Sector Erase Suspend to Erase/Program Suspend,
6. Modify package code for 56-pin TSOP from T to Z in ordering
7. Del table 22 and Figure 20 Temporary Sector Unprotect Timing table
8. Modify Erase/Program performance in Table 20, 21 and 22.
9. Correct typo from Byte to Word on Page 7
10. Del t
11. Modify DC Characteristics in table 15
12. Del apply VID on address pin A9 to access autoselect codes
13. Modify A9 spec from 9.5V to Vcc+0.5V in ABSOLUTE MAXIMUM
14. Modify CFI 4Ah, 4Fh description and data of 4Fh in table 12
1. Modify naming for DQ0 OTP Lock Bit to Secured Silicon Sector
2. Modify Table.8 Secured Silicon Sector Address Range 000000h-
3. Add note “The address 0h~7h in Secured Silicon Sector is reserved
Update FIGURE 23. 64 ball Fortified Ball Grid Array (FBGA), 11 X13
mm, Pitch 1mm package outline on page 52
1. Modify from Sector 0 to all sectors in note 1 of Table 6 and note 2, 3
2. Add “User only can use DQ6 and RY/BY# pin to detect programming
Change the package code of 64-ball BGA on page 53.
Correct typo in Table 20, “
VHH from 10.5~11.5V to 8.5~9.5V
ICC1 5MHz 9 15mA typ, 10MHz 16 25mA typ
ICC4, ICC5 and ICC6 1 1.5uA typ, 5 10uA max
Add IIO2 and IACCspec
from Sector Erase Resume to Erase/Program resume in Table13
information on Page 54
and Diagram and Figure 21.Sector Protect/Unprotect Timing Diagram
function. ( Remove TABLE 5 and modify description Autoselect
section for using High voltage to get Autoselect Codes )
RATINGS
and note 9 of PPB section on page 25.
status” in note 10 on page26.
Chip erase time from 32 30sec typ and 280 120sec max.
Add ACC and total write buffer time spec
Protection Bit on Page 25
000007h from Determined by customer to Reserve for Factory
for Factory“ on Page 31
CEH
in table 17
Rev. H, Issue Date: 2009/10/01
t
B
BUSY
54
“
from Min. to Max on page 42.
©2004 Eon Silicon Solution, Inc.,
EN29GL128H/L
www.eonssi.com
Date
2009/01/23
2009/02/18
2009/5/12
2009/6/19
2009/07/01
2009/7/14
2009/07/22
2009/10/01