ATTINY26L8SU SL383 Atmel, ATTINY26L8SU SL383 Datasheet - Page 99
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
ATTINY26L8SU SL383
Manufacturer Part Number
ATTINY26L8SU SL383
Description
MCU 8-Bit ATtiny AVR RISC 2KB Flash 3.3V/5V 20-Pin SOIC T/R
Manufacturer
Atmel
Datasheet
1.ATTINY26L8PU.pdf
(185 pages)
- Current page: 99 of 185
- Download datasheet (3Mb)
1477J–AVR–06/07
The successive approximation circuitry requires an input clock frequency between
50 kHz and 200 kHz. If a lower resolution than 10 bits is needed, the input clock fre-
quency to the ADC can be as high as 1000 kHz to get a higher sample rate.
The ADC module contains a prescaler, which divides the system clock to an acceptable
ADC clock frequency.
The ADPS bits in ADCSR are used to generate a proper ADC clock input frequency
from any chip clock frequency above 100 kHz. The prescaler starts counting from the
moment the ADC is switched on by setting the ADEN bit in ADCSR. The prescaler
keeps running for as long as the ADEN bit is set, and is continuously reset when ADEN
is low.
When initiating a conversion by setting the ADSC bit in ADCSR, the conversion starts at
the following rising edge of the ADC clock cycle. If differential channels are selected, the
conversion will only start at every other rising edge of the ADC clock cycle after ADEN
was set.
A normal conversion takes 13 ADC clock cycles. In certain situations, the ADC needs
more clock cycles to initialization and minimize offset errors. Extended conversions take
25 ADC clock cycles and occur as the first conversion after the ADC is switched on
(ADEN in ADCSR is set).
Special care should be taken when changing differential channels. Once a differential
channel has been selected, the gain stage may take as much as 125 µs to stabilize to
the new value. Thus conversions should not be started within the first 125 µs after
selecting a new differential channel. Alternatively, conversions results obtained within
this period should be discarded. The same settling time should be observed for the first
differential conversion after changing ADC reference (by changing the REFS1:0 bits in
ADMUX).
The actual sample-and-hold takes place 1.5 ADC clock cycles after the start of a normal
conversion and 13.5 ADC clock cycles after the start of an extended conversion. When
a conversion is complete, the result is written to the ADC Data Registers, and ADIF is
set. In Single Conversion mode, ADSC is cleared simultaneously. The software may
then set ADSC again, and a new conversion will be initiated on the first rising ADC clock
edge. In Free Running mode, a new conversion will be started immediately after the
conversion completes, while ADSC remains high. Using Free Running mode and an
ADC clock frequency of 200 kHz gives the lowest conversion time, 65
15 kSPS. For a summary of conversion times, see Table 43.
Figure 53. ADC Timing Diagram, Extended Conversion (Single Conversion Mode)
Cycle Number
ADC Clock
ADEN
ADSC
ADIF
ADCH
ADCL
1
2
MUX and REFS
Update
12
13
14
15
Sample & Hold
16
Extended Conversion
17
18
19
20
21
22
Conversion
Complete
23
24
ATtiny26(L)
25
MSB of Result
LSB of Result
µs
, equivalent to
Next
Conversion
1
2
MUX and REFS
Update
3
99
Related parts for ATTINY26L8SU SL383
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATTINY26-16MU](/photos/12/13/121313/attiny26-16mu_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16SU](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 20-SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16PU](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 20-DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16MI](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16PI](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 20-DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16SC](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ COM 20-SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16SI](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ IND 20-SOIC
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16MJ](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
ID MCU AVR 2K 5V 16MHZ 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16MQ](/photos/30/99/309943/qfn-32_tmb.jpg)
Part Number:
Description:
Microcontrollers (MCU) AVR 2K FLASH 128B EE 128B SRAM ADC
Manufacturer:
Atmel
Datasheet:
![ATtiny26](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
![ATTINY26-16MC](/photos/12/13/121302/attiny26-16mc_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ COM 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16PC](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 2K 16MHZ COM 20-DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16PJ](/photos/6/80/68043/313-20-dip_tmb.jpg)
Part Number:
Description:
ID MCU AVR 2K 5V 16MHZ 20-DIP
Manufacturer:
Atmel
Datasheet:
![ATTINY26-16SJ](/photos/6/80/68042/453-20-soic_tmb.jpg)
Part Number:
Description:
ID MCU AVR 2K 5V 16MHZ 20-SOIC
Manufacturer:
Atmel
Datasheet: