MT48LC2M32B2TG-6 :G Micron, MT48LC2M32B2TG-6 :G Datasheet - Page 16
![no-image](/images/no-image-200.jpg)
MT48LC2M32B2TG-6 :G
Manufacturer Part Number
MT48LC2M32B2TG-6 :G
Description
DRAM Chip SDRAM 64M-Bit 3.3V 86-Pin TSOP-II
Manufacturer
Micron
Datasheet
1.MT48LC2M32B2B5-7G.pdf
(69 pages)
Operating Mode
Write Burst Mode
Commands
Table 7:
PDF: 09005aef811ce1fe/Source: 09005aef811ce1d5
64MSDRAMx32_2.fm - Rev. J 12/08 EN
Name (Function)
COMMAND INHIBIT (NOP)
NO OPERATION (NOP)
ACTIVE (Select bank and activate row)
READ (Select bank and column, and start READ
burst)
WRITE (Select bank and column, and start WRITE
burst)
BURST TERMINATE
PRECHARGE (Deactivate row in bank or banks)
AUTO REFRESH or SELF REFRESH (Enter self refresh
mode)
LOAD MODE REGISTER
WRITE ENABLE/OUTPUT ENABLE
WRITE INHIBIT/OUTPUT HIGH-Z
Truth Table 1 – Commands and DQM Operation
CKE is HIGH for all commands shown except SELF REFRESH
Notes:
The normal operating mode is selected by setting M7 and M8 to zero; other combina-
tions of values for M7 and M8 are reserved for future use and/or test modes. The
programmed burst length applies to both read and write bursts.
Test modes and reserved states should not be used because unknown operation or
incompatibility with future versions may result.
When M9 = 0, the burst length programmed via M0–M2 applies to both read and write
bursts; when M9 = 1, the programmed burst length applies to read bursts, but write
accesses are single-location (nonburst) accesses.
Truth Table 1 provides a quick reference of available commands. This is followed by a
written description of each command. Three additional Truth Tables appear following
“Operations” on page 19; these tables provide current state/next state information.
1. A0–A10 provide row address, BA0 and BA1 determine which bank is made active.
2. A0–A7 provide column address; A10 HIGH enables the auto precharge feature (nonpersis-
3. A10 LOW: BA0 and BA1 determine the bank being precharged. A10 HIGH: all banks pre-
4. This command is AUTO REFRESH if CKE is HIGH; SELF REFRESH if CKE is LOW.
5. Internal refresh counter controls row addressing; all inputs and I/Os are “Don’t Care” except
6. A0–A10 define the op-code written to the mode register.
7. Activates or deactivates the DQs during WRITEs (zero-clock delay) and READs (two-clock
tent), while A10 LOW disables the auto precharge feature; BA0 and BA1 determine which
bank is being read from or written to.
charged and BA0 and BA1 are “Don’t Care.”
for CKE.
delay). DQM0 controls DQ0–DQ7; DQM1 controls DQ8–DQ15; DQM2 controls DQ16–DQ23;
and DQM3 controls DQ24–DQ31.
CS#
H
L
L
L
L
L
L
L
–
–
L
16
RAS# CAS#
H
H
H
H
X
L
L
L
L
–
–
Micron Technology, Inc., reserves the right to change products or specifications without notice.
X
H
H
H
H
L
L
L
L
–
–
WE#
X
H
H
H
H
L
L
L
L
–
–
DQM
L/H
L/H
X
X
X
X
X
X
X
H
L
7
7
Bank/row
Bank/col
Bank/col
Op-code
©2001 Micron Technology, Inc. All rights reserved.
ADDR
Code
64Mb: x32 SDRAM
X
X
X
X
–
–
High-Z
Active
Active
Valid
Commands
DQs
X
X
X
X
X
X
X
Notes
4, 5
1
2
2
3
6
7
7