PSD4235G2-90U STMicroelectronics, PSD4235G2-90U Datasheet - Page 101
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
PSD4235G2-90U
Manufacturer Part Number
PSD4235G2-90U
Description
IC FLASH 4MBIT 90NS 80TQFP
Manufacturer
STMicroelectronics
Datasheet
1.PSD4235G2-70U.pdf
(129 pages)
Specifications of PSD4235G2-90U
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
4M (512K x 8)
Speed
90ns
Interface
Parallel
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Package / Case
80-TQFP, 80-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-1968
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PSD4235G2-90U
Manufacturer:
MURATA
Quantity:
34 000
Company:
Part Number:
PSD4235G2-90U
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
PSD4235G2-90U
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
PSD4235G2-90UI
Manufacturer:
TI
Quantity:
8 802
Company:
Part Number:
PSD4235G2-90UI
Manufacturer:
STMicroelectronics
Quantity:
10 000
PSD4235G2
23
Note:
23.1
Programming in-circuit using the JTAG serial
interface
The JTAG Serial Interface on the PSD can be enabled on Port E (see
blocks (primary Flash memory and secondary Flash memory), PLD logic, and PSD
Configuration bits may be programmed through the JTAG-ISC Serial Interface. A blank
device can be mounted on a printed circuit board and programmed using JTAG In-System
Programming (ISP).
The standard JTAG signals (IEEE 1149.1) are TMS, TCK, TDI, and TDO. Two additional
signals, TSTAT and TERR, are optional JTAG extensions used to speed up Program and
Erase cycles.
By default, on a blank PSD (as shipped from the factory, or after erasure), four pins on Port
E are enabled for the basic JTAG signals TMS, TCK, TDI, and TDO.
See Application Note AN1153 for more details on JTAG In-System Programming (ISP).
Standard JTAG signals
The standard JTAG signals (TMS, TCK, TDI, and TDO) can be enabled by any of three
different conditions that are logically ORed. When enabled, TDI, TDO, TCK, and TMS are
inputs, waiting for a serial command from an external JTAG controller device (such as
FlashLINK or Automated Test Equipment). When the enabling command is received from
the external JTAG controller device, TDO becomes an output and the JTAG channel is fully
functional inside the PSD. The same command that enables the JTAG channel may
optionally enable the two additional JTAG pins, TSTAT and TERR.
The following symbolic logic equation specifies the conditions enabling the four basic JTAG
pins (TMS, TCK, TDI, and TDO) on their respective Port E pins. For purposes of discussion,
the logic label JTAG_ON is used. When JTAG_ON is true, the four pins are enabled for
JTAG. When JTAG_ON is false, the four pins can be used for general PSD I/O.
JTAG_ON = PSDsoft Express_enabled +
in the PSDsoft Express Configuration utility. This dedicates the
pins for JTAG at all times (compliant with IEEE 1149.1 */
Microcontroller_enabled +
PSD register, JTAG Enable. This register is located at address CSIOP
+ offset C7h. Setting the JTAG_ENABLE bit in this register will
enable the pins for JTAG use. This bit is cleared by a PSD reset or
the microcontroller. See
PSD_product_term_enabled;
enable the JTAG pins. This PT has the reserved name JTAGSEL. Once
defined as a node in PSDabel, the designer can write an equation for
JTAGSEL. This method is used when the Port E JTAG pins are
multiplexed with other I/O signals. It is recommended to tie
logically the node JTAGSEL to the JEN\ signal on the Flashlink cable
when multiplexing JTAG signals. See Application Note 1153 for
details. */
/* An NVM configuration bit inside the PSD is set by the designer
/* The microcontroller can set a bit at run-time by writing to the
/* A dedicated product term (PT) inside the PSD can be used to
Programming in-circuit using the JTAG serial interface
Table 21
for bit definition. */
Table
52). All memory
101/129