TLE7184F Infineon Technologies, TLE7184F Datasheet - Page 26

• Manufacturer Part Number: TLE7184F
• Description: IC DRIVER 3PH BRIDGE 48-VQFN
• Manufacturer: Infineon Technologies

Specifications of TLE7184F

• Applications: DC Motor Controller, Brushless (BLDC), 3 Phase
• Number Of Outputs: 1
• Voltage - Supply: 6 V ~ 45 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: 48-VFQFN
• Mounting Style: SMD/SMT
• Packages: PG-VQFN-48
• Operating Range: 7.0 - 32.0 V
• Iq: 50 ?A
• Turn On/off Current: -
• D.c.-range @ 20khz: 0...95%
• Numbers Of Integrated Opamps For Load Current Measurement: 1.0
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Voltage - Load: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: SP000362096

As long as the VS Under Voltage Lock Out is not reached, the low side MOSFETs will stay actively switched off.
The status of the high side MOSFET drivers is dependent on the bootstrap voltage - which depends on the SHx
voltage. It is expected that the SHx will be pulled to VDH level by the high side MOSFETs and this will switch off
the high side MOSFETs passively.
In this situation the short circuit detection of this output stage is deactivated to avoid wrong error reporting.
9.2.8
The TLE7184F has an integrated VREG Under Voltage Shut Down, to avoid operation with VREG shorted to GND.
If the supply voltage at VREG reaches the Under Voltage shut down level
Prewarning is set “AND” the wake up time is expired, VREG will be switched off and the IC will go to the VREG
Shut Down Mode. In this condition the µC is still supplied and can communicate via the PWM interface (IFMA),
the MOSFETs are switched off and an error is set. The only way to leave this mode is to go to Sleep Mode.
If the supply voltage at VREG reaches the Under Voltage shut down level
Prewarning is set and the wake-up time is expired, VREG and VDD will be switched off and the IC will go to the
“Dead Lock Mode”.
The only way to leave this Deadlock Mode is to provoke a VS Under Voltage Shut Down, for example by removing
battery voltage.
9.2.9
The TLE7184F has an integrated Over Voltage shut down to minimize risk of destruction of the IC at high supply
voltages caused by violation of the maximum ratings.
The voltage is observed at the Over Voltage input pin IOV and at the VDH pin. If the voltage at the IOV pin or at
the VDH exceeds the Over Voltage shut down level for more than the specified filter time the IC goes into Error
Mode.
The effective Over Voltage level can be adjusted by a voltage divider at IOV connected to VDHS. The Over
Voltage level at VDH is fix.
9.2.10
In bridge applications it has to be assured that the external high side and low side MOSFETs are not “on” at the
same time, connecting directly the battery voltage to GND. The dead time generated in the TLE7184F is fixed to
a minimum value if the DT pin is connected to GND. This function assures a minimum dead time if a common input
signal for ILx and IHx is used.
The dead time can be increased beyond the internal fixed dead time by connecting the DT pin via a dead time
resistor R
If an exact dead time of the bridge is needed the use of the µC PWM generation unit is recommended.
In case of an open DT pin, the dead time is set to the internal maximum value.
In addition to this dead time, the TLE7184F provides a locking mechanism, avoiding that both external MOSFETs
of one half bridge can be switched on at the same time. This functionality is called shoot through protection.
If the command to switch on both high and low side switches in the same half bridge is given at the input pins, the
command will be ignored. The outputs will stay in the situation like before the conflicting input.
9.2.11
The TLE7184F provides a short circuit protection for the external MOSFETs. It is a monitoring of the drain-source
voltage of the external MOSFETs. (see
The drain-source voltage monitoring of the short circuit detection for a certain external MOSFET is active as soon
as the corresponding driver output stage is set to “on”, the dead time and the blanking time is expired.
Data Sheet
DT
to GND - the larger the dead time resistor the larger the dead time.
VREG Under Voltage Shut Down (VREG_UVSD)
IOV and VDH Over Voltage Shut Down (IOV_OVSD, VDH_OVSD)
Dead Time and Shoot Through Protection
Short Circuit Protection (SCP)
Figure 3
Description of Modes, Protection and Diagnostic Functions
)
26
V
VRSD
V
VRSD
, “AND” no Over Temperature
, “AND” Over Temperature
Rev. 1.0, 2008-12-04
TLE7184F