MT18HTF12872AY-53EB1 Micron Technology Inc, MT18HTF12872AY-53EB1 Datasheet - Page 7
![MODULE SDRAM DDR2 1GB 240DIMM](/photos/7/83/78383/mfg557-240-dimm_sml.jpg)
MT18HTF12872AY-53EB1
Manufacturer Part Number
MT18HTF12872AY-53EB1
Description
MODULE SDRAM DDR2 1GB 240DIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT18HTF12872AY-53EB1.pdf
(18 pages)
Specifications of MT18HTF12872AY-53EB1
Memory Type
DDR2 SDRAM
Memory Size
1GB
Speed
533MT/s
Package / Case
240-DIMM
Main Category
DRAM Module
Sub-category
DDR2 SDRAM
Module Type
240UDIMM
Device Core Size
72b
Organization
128Mx72
Total Density
1GByte
Chip Density
512Mb
Access Time (max)
50ps
Maximum Clock Rate
533MHz
Operating Supply Voltage (typ)
1.8V
Operating Current
1.368A
Number Of Elements
18
Operating Supply Voltage (max)
1.9V
Operating Supply Voltage (min)
1.7V
Operating Temp Range
0C to 85C
Operating Temperature Classification
Commercial
Pin Count
240
Mounting
Socket
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
General Description
Serial Presence-Detect Operation
PDF: 09005aef80e8ad4d/Source: 09005aef80e785e6
HTF18C64_128_256_512x72A.fm - Rev. H 5/08 EN
The MT18HTF6472A, MT18HTF12872A, MT18HTF25672A, and MT18HTF51272A DDR2
SDRAM modules are high-speed, CMOS, dynamic random-access 512MB, 1GB, 2GB,
and 4GB memory modules organized in a x72 configuration. These DDR2 SDRAM
modules use internally configured 4-bank (256Mb, 512Mb) or 8-bank (1Gb, 2Gb) DDR2
SDRAM devices.
DDR2 SDRAM modules use double data rate architecture to achieve high-speed opera-
tion. The double data rate architecture is essentially a 4n-prefetch architecture with an
interface designed to transfer two data words per clock cycle at the I/O pins. A single
read or write access for the DDR2 SDRAM module effectively consists of a single 4n-bit-
wide, one-clock-cycle data transfer at the internal DRAM core and four corresponding
n-bit-wide, one-half-clock-cycle data transfers at the I/O pins.
A bidirectional data strobe (DQS, DQS#) is transmitted externally, along with data, for
use in data capture at the receiver. DQS is a strobe transmitted by the DDR2 SDRAM
device during READs and by the memory controller during WRITEs. DQS is edge-
aligned with data for READs and center-aligned with data for WRITEs.
DDR2 SDRAM modules operate from a differential clock (CK and CK#); the crossing of
CK going HIGH and CK# going LOW will be referred to as the positive edge of CK.
Commands (address and control signals) are registered at every positive edge of CK.
Input data is registered on both edges of DQS, and output data is referenced to both
edges of DQS, as well as to both edges of CK.
DDR2 SDRAM modules incorporate serial presence-detect (SPD). The SPD function is
implemented using a 2,048-bit EEPROM. This nonvolatile storage device contains
256 bytes. The first 128 bytes can be programmed by Micron to identify the module type
and various SDRAM organizations and timing parameters. The remaining 128 bytes of
storage are available for use by the customer. System READ/WRITE operations between
the master (system logic) and the slave EEPROM device occur via a standard I
using the DIMM’s SCL (clock) and SDA (data) signals, together with SA (2:0), which
provide eight unique DIMM/EEPROM addresses. Write protect (WP) is tied to V
module, permanently disabling hardware write protect.
512MB, 1GB, 2GB, 4GB (x72, DR, ECC) 240-Pin DDR2 SDRAM UDIMM
7
Micron Technology, Inc., reserves the right to change products or specifications without notice.
General Description
©2003 Micron Technology, Inc. All rights reserved.
2
C bus
SS
on the