PIC18F26K20-E/SO Microchip Technology, PIC18F26K20-E/SO Datasheet - Page 221

• Manufacturer Part Number: PIC18F26K20-E/SO
• Description: IC PIC MCU FLASH 16KX16 28-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F26K20-E/SO

• Program Memory Type: FLASH
• Program Memory Size: 64KB (32K x 16)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 1K x 8
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3936 B
• Interface Type: CCP/ECCP/EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 64 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPAC164303 - MODULE SKT FOR PM3 64TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

17.4.7
In I
reload value is placed in the SSPADD register
(Figure 17-17). When a write occurs to SSPBUF, the
Baud Rate Generator will automatically begin counting.
The BRG counts down to ‘0’ and stops until another
reload has taken place. The BRG count is decre-
mented twice per instruction cycle (T
Q4 clocks. In I
automatically. One half of the SCL period is equal to
[(SSPADD+1)  2]/F
(F
FIGURE 17-17:
TABLE 17-3:
 2010 Microchip Technology Inc.
Note 1:
CY
2
C Master mode, the Baud Rate Generator (BRG)
/F
SCL
) -1.
64 MHz
64 MHz
64 MHz
40 MHz
40 MHz
40 MHz
16 MHz
16 MHz
16 MHz
4 MHz
The I
100 kHz) in all details, but may be used with care where higher rates are required by the application.
BAUD RATE
F
OSC
2
C Master mode, the BRG is reloaded
2
C interface does not conform to the 400 kHz I
I
2
C™ CLOCK RATE W/BRG
BAUD RATE GENERATOR BLOCK DIAGRAM
OSC
SSPM<3:0>
. Therefore SSPADD =
SCL
CY
) on the Q2 and
16 MHz
16 MHz
16 MHz
10 MHz
10 MHz
10 MHz
SSPM<3:0>
4 MHz
4 MHz
4 MHz
1 MHz
F
CY
Reload
Control
CLKOUT
Reload
Once
transmission of the last data bit is followed by ACK), the
internal clock will automatically stop counting and the
SCL pin will remain in its last state.
Table 17-3 demonstrates clock rates based on
instruction cycles and the BRG value loaded into
SSPADD.
The minimum SSPADD value for baud rate generation
is 0x03.
2
PIC18F2XK20/4XK20
BRG Down Counter
C specification (which applies to rates greater than
SSPADD<7:0>
BRG Value
the
0Ch
3Fh
1Fh
27h
32h
18h
63h
09h
27h
09h
given
operation
F
OSC
(2 Rollovers of BRG)
/2
is
400 kHz
400 kHz
400 kHz
313.7 kHz
312.5 kHz
DS41303G-page 221
250 kHz
100 kHz
308 kHz
100 kHz
100 kHz
F
complete
SCL
(1)
(1)
(1)
(i.e.,