PIC24FJ64GA006-I/PT Microchip Technology, PIC24FJ64GA006-I/PT Datasheet - Page 57

• Manufacturer Part Number: PIC24FJ64GA006-I/PT
• Description: IC PIC MCU FLASH 32KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ64GA006-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 64KB (22K x 24)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240011, DV164033, MA240013, AC164127, DM240001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Controller Family/series: PIC24
• No. Of I/o's: 53
• Ram Memory Size: 8KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Embedded Interface Type: I2C, SPI, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM240011 - KIT STARTER MPLAB FOR PIC24F MCUDV164033 - KIT START EXPLORER 16 MPLAB ICD2MA160011 - DAUGHTER BOARD PICDEM LCD 16F91XDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

5.2.1
The oscillator start-up circuitry and its associated delay
timers are not linked to the device Reset delays that
occur at power-up. Some crystal circuits (especially
low-frequency crystals) will have a relatively long
start-up time. Therefore, one or more of the following
conditions is possible after SYSRST is released:
• The oscillator circuit has not begun to oscillate.
• The Oscillator Start-up Timer has NOT expired (if
• The PLL has not achieved a LOCK (if PLL is used).
The device will not begin to execute code until a valid
clock source has been released to the system. There-
fore, the oscillator and PLL start-up delays must be
considered when the Reset delay time must be known.
5.2.2
If the FSCM is enabled, it will begin to monitor the sys-
tem clock source when SYSRST is released. If a valid
clock source is not available at this time, the device will
automatically switch to the FRC oscillator and the user
can switch to the desired crystal oscillator in the Trap
Service Routine.
5.2.2.1
When the system clock source is provided by a crystal
oscillator and/or the PLL, a small delay, T
automatically be inserted after the POR and PWRT
delay times. The FSCM will not begin to monitor the
system clock source until this delay expires. The FSCM
delay time is nominally 100 μs and provides additional
time for the oscillator and/or PLL to stabilize. In most
cases, the FSCM delay will prevent an oscillator failure
trap at a device Reset when the PWRT is disabled.
© 2009 Microchip Technology Inc.
a crystal oscillator is used).
POR AND LONG OSCILLATOR
START-UP TIMES
FAIL-SAFE CLOCK MONITOR
(FSCM) AND DEVICE RESETS
FSCM Delay for Crystal and PLL
Clock Sources
FSCM
PIC24FJ128GA010 FAMILY
, will
5.3
Most of the Special Function Registers (SFRs) associ-
ated with the PIC24F CPU and peripherals are reset to a
particular value at a device Reset. The SFRs are
grouped by their peripheral or CPU function and their
Reset values are specified in each section of this manual.
The Reset value for each SFR does not depend on the
type of Reset, with the exception of four registers. The
Reset value for the Reset Control register, RCON, will
depend on the type of device Reset. The Reset value
for the Oscillator Control register, OSCCON, will
depend on the type of Reset and the programmed val-
ues of the oscillator Configuration bits in the FOSC
Device Configuration register (see Table 5-2). The
RCFGCAL and NVMCON registers are only affected
by a POR.
Special Function Register Reset
States
DS39747E-page 57