MCHC908GR8ACFAE Freescale Semiconductor, MCHC908GR8ACFAE Datasheet - Page 166

• Manufacturer Part Number: MCHC908GR8ACFAE
• Description: IC MCU 8K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908GR8ACFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 7.5KB (7.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08G
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Enhanced Serial Communications Interface (ESCI) Module
TE — Transmitter Enable Bit
RE — Receiver Enable Bit
RWU — Receiver Wakeup Bit
SBK — Send Break Bit
166
Setting this read/write bit begins the transmission by sending a preamble of 10 or 11 1s from the
transmit shift register to the TxD pin. If software clears the TE bit, the transmitter completes any
transmission in progress before the TxD returns to the idle condition (1). Clearing and then setting TE
during a transmission queues an idle character to be sent after the character currently being
transmitted. Reset clears the TE bit.
Setting this read/write bit enables the receiver. Clearing the RE bit disables the receiver but does not
affect receiver interrupt flag bits. Reset clears the RE bit.
This read/write bit puts the receiver in a standby state during which receiver interrupts are disabled.
The WAKE bit in SCC1 determines whether an idle input or an address mark brings the receiver out
of the standby state and clears the RWU bit. Reset clears the RWU bit.
Setting and then clearing this read/write bit transmits a break character followed by a 1. The 1 after the
break character guarantees recognition of a valid start bit. If SBK remains set, the transmitter
continuously transmits break characters with no 1s between them. Reset clears the SBK bit.
1 = Transmitter enabled
0 = Transmitter disabled
1 = Receiver enabled
0 = Receiver disabled
1 = Standby state
0 = Normal operation
1 = Transmit break characters
0 = No break characters being transmitted
Writing to the TE bit is not allowed when the enable ESCI bit (ENSCI) is
clear. ENSCI is in ESCI control register 1.
Writing to the RE bit is not allowed when the enable ESCI bit (ENSCI) is
clear. ENSCI is in ESCI control register 1.
Do not toggle the SBK bit immediately after setting the SCTE bit. Toggling
SBK before the preamble begins causes the ESCI to send a break
character instead of a preamble.
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
NOTE
NOTE
NOTE
Freescale Semiconductor