MCHC908GR8ACFAE Freescale Semiconductor, MCHC908GR8ACFAE Datasheet - Page 81

• Manufacturer Part Number: MCHC908GR8ACFAE
• Description: IC MCU 8K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908GR8ACFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 7.5KB (7.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 384Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08G
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 384 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8.2 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 6 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

7.3.2.1 Digitally Controlled Oscillator
The digitally controlled oscillator (DCO) is an inaccurate oscillator which generates the internal clock
(ICLK). The clock period of ICLK is dependent on the digital loop filter outputs (DSTG[7:0] and DDIV[3:0]).
Because of only a limited number of bits in DDIV and DSTG, the precision of the output (ICLK) is restricted
to a precision of approximately ±0.202 percent to ±0.368 percent when measured over several cycles (of
the desired frequency). Additionally, since the propagation delays of the devices used in the DCO ring
oscillator are a measurable fraction of the bus clock period, reaching the long-term precision may require
alternately running faster and slower than desired, making the worst case cycle-to-cycle frequency
variation ±6.45 percent to ±11.8 percent (of the desired frequency). The valid values of DDIV:DSTG range
from $000 to $9FF. For more information on the quantization error in the DCO, see
Error in DCO
7.3.2.2 Modulo N Divider
The modulo N divider creates the low-frequency base clock (IBASE) by dividing the internal clock (ICLK)
by the ICG multiplier factor (N), contained in the ICG multiplier register (ICGMR). When N is programmed
to a $01 or $00, the divider is disabled and ICLK is passed through to IBASE undivided. When the internal
clock generator is stable, the frequency of IBASE will be equal to the nominal frequency (f
kHz ± 25 percent.
Freescale Semiconductor
VOLTAGE AND
ICGEN
REFERENCES
CURRENT
Output.
NAME
NAME
MC68HC908GT16 • MC68HC908GT8 • MC68HC08GT16 Data Sheet, Rev. 5.0
Figure 7-3. Internal Clock Generator Block Diagram
CONFIG2 REGISTER BIT
TOP LEVEL SIGNAL
–
– –
++
+
CLOCK GENERATOR
COMPARATOR
FREQUENCY
DIGITAL
FILTER
TRIM[7:0]
LOOP
CONTROLLED
OSCILLATOR
DIGITALLY
MODULO
DIVIDER
N[6:0]
N
NAME
NAME
MODULE SIGNAL
REGISTER BIT
Functional Description
7.4.4 Quantization
DSTG[7:0]
DDIV[3:0]
FICGS
IBASE
NOM
ICLK
) of 307.2
81