MCF5282CVF80J Freescale Semiconductor, MCF5282CVF80J Datasheet - Page 430

• Manufacturer Part Number: MCF5282CVF80J
• Description: IC MPU 512K FLASH 256MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5282CVF80J

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 150
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Processor Series: MCF528x
• Core: ColdFire V2
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: NNDK-MOD5282-KIT
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: No

UART Modules
Table 23-7
Operating
23-10
MISC
Field
6–4
7
IPSBAR
Offset:
Reset:
Reserved, must be cleared.
MISC Field (this field selects a single command)
W
R
Modes,” show how these commands are used.
describes UCRn fields and commands. Examples in
0x00_0208 (UCR0)
0x00_0248 (UCR1)
0x00_0288 (UCR2)
000
001
010
011
100
101
110
111
0
0
7
NO COMMAND
RESET MODE
REGISTER POINTER
RESET RECEIVER
RESET
TRANSMITTER
RESET ERROR
STATUS
RESET BREAK
CHANGE INTERRUPT
START BREAK
STOP BREAK
Command
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
6
0
Figure 23-7. UART Command Registers (UCRn)
–
Table 23-7. UCRn Field Descriptions
—
Causes the mode register pointer to point to UMR1n.
Immediately disables the receiver, clears USRn[FFULL,RXRDY], and reinitializes
the receiver FIFO pointer. No other registers are altered. Because it places the
receiver in a known state, use this command instead of
reconfiguring the receiver.
Immediately disables the transmitter and clears USRn[TXEMP,TXRDY]. No other
registers are altered. Because it places the transmitter in a known state, use this
command instead of
Clears USRn[RB,FE,PE,OE]. Also used in block mode to clear all error bits after
a data block is received.
Clears the delta break bit, UISRn[DB].
Forces UTXDn low. If the transmitter is empty, break may be delayed up to one bit
time. If the transmitter is active, break starts when character transmission
completes. Break is delayed until any character in the transmitter shift register is
sent. Any character in the transmitter holding register is sent after the break.
Transmitter must be enabled for the command to be accepted. This command
ignores the state of UCTSn.
Causes UTXDn to go high (mark) within two bit times. Any characters in the
transmit buffer are sent.
MISC
0
5
0
4
Description
TRANSMITTER DISABLE
0
3
Section 23.4.2, “Transmitter and Receiver
Description
TC
when reconfiguring the transmitter.
0
2
RECEIVER DISABLE
Access: User write-only
Freescale Semiconductor
0
1
RC
0
when
0