M30620FCAFP#U5 Renesas Electronics America, M30620FCAFP#U5 Datasheet - Page 329

• Manufacturer Part Number: M30620FCAFP#U5
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30620FCAFP#U5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-QFP
• Package: 100PQFP
• Family Name: M16C
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: SIM/UART
• On-chip Adc: 10-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Timer A
2-10
Figure 2.2.4. Timer A-related registers (3)
Up/down flag (Note 1)
b7
One-shot start flag
b7
b6
b6
b5
b5
b4
b4
b3
b3
b2
b2
b1
b1
b0
b0
Note 1: Use MOV instruction to write to this register.
Note 2: Set the TAi
Note: Set the corresponding port direction register to “0”.
Bit symbol
Nothing is assigned.
In an attempt to write to this bit, write “0”. The value, if read, turns out to be indeterminate.
Bit symbol
TA0UD
TA1UD
TA2UD
TA3UD
TA4UD
TA2P
TA3P
TA4P
TA0TGL
TA0TGH
TA0OS
TA1OS
TA2OS
TA3OS
TA4OS
Symbol
UDF
Symbol
ONSF
Timer A3 two-phase pulse
signal processing select bit
Timer A0 up/down flag
Timer A1 up/down flag
Timer A2 up/down flag
Timer A3 up/down flag
Timer A4 up/down flag
Timer A2 two-phase pulse
signal processing select bit
Timer A4 two-phase pulse
signal processing select bit
Timer A0 event/trigger
select bit
Timer A0 one-shot start flag
Timer A1 one-shot start flag
Timer A2 one-shot start flag
Timer A3 one-shot start flag
Timer A4 one-shot start flag
IN
Address
0382
Bit name
Address
and TAi
0384
Bit name
16
16
OUT
pins correspondent port direction registers to “0”.
When reset
0 : Down count
1 : Up count
This specification becomes valid
when the up/down flag content is
selected for up/down switching
cause
0 : two-phase pulse signal
1 : two-phase pulse signal
When not using the two-phase
pulse signal processing function,
set the select bit to “0”
When reset
00X00000
b7 b6
0 0 :
0 1 : TB2 overflow is selected
1 0 : TA4 overflow is selected
1 1 : TA1 overflow is selected
00
1 : Timer start
processing disabled
processing enabled (Note 2)
16
When read, the value is “0”
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Input on TA0
2
Function
Function
IN
is selected (Note)
M16C / 62A Group
Mitsubishi microcomputers
R
W
R
W