UPD78F0500MC-5A4-A Renesas Electronics America, UPD78F0500MC-5A4-A Datasheet - Page 500

• Manufacturer Part Number: UPD78F0500MC-5A4-A
• Description: MCU 8BIT FLASH SSOP
• Manufacturer: Renesas Electronics America
• Series: 78K0/Kx2r

Specifications of UPD78F0500MC-5A4-A

• Core Processor: 78K/0
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

78K0/Kx2
16.4.2 3-wire serial I/O mode
serial input (SI1n) lines.
(1) Registers used
R01UH0008EJ0401 Rev.4.01
Jul 15, 2010
Address: FF88H After reset: 00H R/W
CSIM11
The 3-wire serial I/O mode is used for connecting peripheral ICs and display controllers with a clocked serial interface.
In this mode, communication is executed by using three lines: the serial clock (SCK1n), serial output (SO1n), and
Symbol
• Serial operation mode register 1n (CSIM1n)
• Serial clock selection register 1n (CSIC1n)
• Port mode register 0 (PM0) or port mode register 1 (PM1)
• Port register 0 (P0) or port register 1 (P1)
The basic procedure of setting an operation in the 3-wire serial I/O mode is as follows.
<1> Set the CSIC1n register (see Figures 16-5 and 16-6).
<2> Set bits 4 to 6 (DIR1n, SSE11 (serial interface CSI11 only), and TRMD1n) of the CSIM1n register (see Figures
<3> Set bit 7 (CSIE1n) of the CSIM1n register to 1. → Transmission/reception is enabled.
<4> Write data to transmit buffer register 1n (SOTB1n). → Data transmission/reception is started.
Caution Take relationship with the other party of communication when setting the port mode register and
Remark n = 0:
• Serial operation mode register 11 (CSIM11)
Notes 1.
16-3 and 16-4).
Read data from serial I/O shift register 1n (SIO1n). → Data reception is started.
port register.
n = 0, 1: 78K0/KE2 products whose flash memory is at least 48 KB, and 78K0/KF2 products
CSIE11
CSIE11
2.
<7>
0
To use P02/SO11, P04/SCK11, and P05/SSI11/TI001 as general-purpose ports, set CSIM11 in the
default status (00H).
Bit 0 (CSOT11) of CSIM11 and serial I/O shift register 11 (SIO11) are reset.
78K0/KE2 products whose flash memory is less than 32 KB, and 78K0/KB2, 78K0/KC2,
78K0/KD2 products
Disables operation
TRMD11
6
SSE11
Note 1
5
and asynchronously resets the internal circuit
Operation control in 3-wire serial I/O mode
CHAPTER 16 SERIAL INTERFACES CSI10 AND CSI11
DIR11
4
3
0
2
0
Note 2
.
1
0
CSOT11
0
500