ATMEGA2560R231-CU Atmel, ATMEGA2560R231-CU Datasheet - Page 192

• Manufacturer Part Number: ATMEGA2560R231-CU
• Description: BUNDLE ATMEGA2560/RF231 PBGA
• Manufacturer: Atmel

Specifications of ATMEGA2560R231-CU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee, 6LoWPAN, RF4CE, SP100, WirelessHART™, ISM
• Data Interface: PCB, Surface Mount
• Memory Size: 256kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 100-CBGA and 32-QFN
• Processor Series: ATMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 256 KB
• Data Ram Size: 8 KB
• Development Tools By Supplier: ATAVRRZ541, ATAVRRAVEN, ATAVRRZRAVEN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Supply: -
• Power - Output: -
• Operating Temperature: -
• Applications: -
• Sensitivity: -
• Data Rate - Maximum: -
• Current - Transmitting: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Details

19.10.6
2549M–AVR–09/10
ASSR – Asynchronous Status Register
• Bit 6 – EXCLK: Enable External Clock Input
When EXCLK is written to one, and asynchronous clock is selected, the external clock input buf-
fer is enabled and an external clock can be input on Timer Oscillator 1 (TOSC1) pin instead of a
32 kHz crystal. Writing to EXCLK should be done before asynchronous operation is selected.
Note that the crystal Oscillator will only run when this bit is zero.
• Bit 5 – AS2: Asynchronous Timer/Counter2
When AS2 is written to zero, Timer/Counter2 is clocked from the I/O clock, clk
written to one, Timer/Counter2 is clocked from a crystal Oscillator connected to the Timer Oscil-
lator 1 (TOSC1) pin. When the value of AS2 is changed, the contents of TCNT2, OCR2A,
OCR2B, TCCR2A and TCCR2B might be corrupted.
• Bit 4 – TCN2UB: Timer/Counter2 Update Busy
When Timer/Counter2 operates asynchronously and TCNT2 is written, this bit becomes set.
When TCNT2 has been updated from the temporary storage register, this bit is cleared by hard-
ware. A logical zero in this bit indicates that TCNT2 is ready to be updated with a new value.
• Bit 3 – OCR2AUB: Output Compare Register2 Update Busy
When Timer/Counter2 operates asynchronously and OCR2A is written, this bit becomes set.
When OCR2A has been updated from the temporary storage register, this bit is cleared by hard-
ware. A logical zero in this bit indicates that OCR2A is ready to be updated with a new value.
• Bit 2 – OCR2BUB: Output Compare Register2 Update Busy
When Timer/Counter2 operates asynchronously and OCR2B is written, this bit becomes set.
When OCR2B has been updated from the temporary storage register, this bit is cleared by hard-
ware. A logical zero in this bit indicates that OCR2B is ready to be updated with a new value.
• Bit 1 – TCR2AUB: Timer/Counter Control Register2 Update Busy
When Timer/Counter2 operates asynchronously and TCCR2A is written, this bit becomes set.
When TCCR2A has been updated from the temporary storage register, this bit is cleared by
hardware. A logical zero in this bit indicates that TCCR2A is ready to be updated with a new
value.
• Bit 0 – TCR2BUB: Timer/Counter Control Register2 Update Busy
When Timer/Counter2 operates asynchronously and TCCR2B is written, this bit becomes set.
When TCCR2B has been updated from the temporary storage register, this bit is cleared by
hardware. A logical zero in this bit indicates that TCCR2B is ready to be updated with a new
value.
If a write is performed to any of the five Timer/Counter2 Registers while its update busy flag is
set, the updated value might get corrupted and cause an unintentional interrupt to occur.
Bit
(0xB6)
Read/Write
Initial Value
R
7
–
0
EXCLK
R/W
6
0
AS2
R/W
5
0
ATmega640/1280/1281/2560/2561
TCN2UB
R
4
0
OCR2AUB
R
3
0
OCR2BUB
R
2
0
TCR2AUB
R
1
0
TCR2BUB
I/O
. When AS2 is
R
0
0
ASSR
192