S9S12XS128J1MAL Freescale Semiconductor, S9S12XS128J1MAL Datasheet - Page 601

• Manufacturer Part Number: S9S12XS128J1MAL
• Description: IC MCU 16BIT 128KB FLSH 112LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of S9S12XS128J1MAL

• Core Processor: HCS12X
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 8K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.72 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 112-LQFP
• Processor Series: S12XS
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: CAN, SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 12
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: DEMO9S12XSFAME, EVB9S12XEP100
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Upon clearing CCIF to launch the Erase Verify D-Flash Section command, the Memory Controller will
verify the selected section of D-Flash memory is erased. The CCIF flag will set after the Erase Verify
D-Flash Section operation has completed.
19.4.2.15 Program D-Flash Command
The Program D-Flash operation programs one to four previously erased words in the D-Flash block. The
Program D-Flash operation will confirm that the targeted location(s) were successfully programmed upon
completion.
Freescale Semiconductor
Register
FSTAT
A Flash word must be in the erased state before being programmed.
Cumulative programming of bits within a Flash word is not allowed.
Table 19-59. Erase Verify D-Flash Section Command FCCOB Requirements
Table 19-60. Erase Verify D-Flash Section Command Error Handling
CCOBIX[2:0]
Table 19-61. Program D-Flash Command FCCOB Requirements
MGSTAT1
MGSTAT0
ACCERR
Error Bit
FPVIOL
CCOBIX[2:0]
000
001
010
011
100
000
001
010
S12XS Family Reference Manual, Rev. 1.11
Set if CCOBIX[2:0] != 010 at command launch
Set if command not available in current mode (see
Set if an invalid global address [22:0] is supplied
Set if a misaligned word address is supplied (global address [0] != 0)
Set if the requested section breaches the end of the D-Flash block
None
Set if any errors have been encountered during the read
Set if any non-correctable errors have been encountered during the read
Global address [15:0] of the first word to be verified
Global address [15:0] of word to be programmed
0x11
Word 1 program value, if desired
Word 2 program value, if desired
0x10
Number of words to be verified
CAUTION
Word 0 program value
FCCOB Parameters
FCCOB Parameters
Global address [22:16] to
identify the D-Flash block
Error Condition
Global address [22:16] to
identify the D-Flash block
128 KByte Flash Module (S12XFTMR128K1V1)
Table
19-28)
601