S183E BANNER ENGINEERING, S183E Datasheet - Page 19

• Manufacturer Part Number: S183E
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING
• Type: Opposed Moder

Specifications of S183E

• Output Current: 150mA
• Supply Voltage Range Dc: 10V To 30V
• Contact Current Max: 300mA
• Switch Terminals: Cable
• Sensor Housing: Barrel
• Sensor Input: Optical
• Sensing Range Max: 20m
• Sensing Mode: Opposed
• Brand/series: S18
• Current, Switching: 300 mA
• Humidity: 90% @ 50 °C (Non-Condensing)
• Ip Rating: IP69K
• Length, Cable: 6.5 ft.
• Material, Housing: PBT Polyester
• Material, Lens: Polycarbonate⁄Acrylic
• Output: SPST
• Primary Type: Photoelectric
• Range, Measurement: 66 mm
• Response Time: 16 ms (ON), 8 ms (OFF)
• Standards: CE Mark, CSA Certified, UL Listed
• Technology: Photoelectric
• Temperature, Operating: -40 to +70 °C
• Termination: Cable
• Vibration: 10 to 60 Hz (Max.)
• Voltage, Supply: 250 VAC
• Lead Free Status / Rohs Status: RoHS Exempt Product

Supply Voltage and Current
Supply Protection Circuitry
Output Configuration
Output Rating
Output Protection Circuitry
Output Response Time
Repeatability
Adjustments
Indicators
Construction
Environmental Rating
Connections
Operating Conditions
Application Notes
Certifications
Hookup Diagrams
10 to 30V dc (10% max. ripple) at less than 45 mA, exclusive of load
Protected against reverse polarity and transient voltages
Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor. Configuration in
TEACH sequence for Light Operate (LO) or Dark Operate (DO).
150 mA max. each output at 25° C, derated to 100 mA at 70° C (derate ≈ 1 mA per ° C)
Off-state leakage current: less than 5 µA @ 30V dc
Output saturation voltage (PNP output): less than 1 volt at 10 mA and less than 2 volts at 150 mA
Output saturation voltage (NPN output): less than 200 millivolts at 10 mA and less than 1 volt at 150 mA
Protected against false pulse on power-up and continuous overload or short-circuit of outputs
Sensors will respond to either a “light” or a “dark” signal of 500 microseconds or longer duration, 1 kHz max.
NOTE: 1 second delay on power-up; outputs do not conduct during this time.
100 microseconds (all models)
Push-button TEACH mode sensitivity setting; remote TEACH mode input is provided (gray wire)
Two LEDs: Yellow and Bicolor Green/Red
Green (RUN Mode):
Red (TEACH Mode):
Yellow (TEACH Mode): ON to indicate sensor is ready to learn output ON condition
Yellow (RUN Mode):
Reinforced thermoplastic polyester housing, totally encapsulated, o-ring seal, acrylic lenses, and stainless steel screws.
Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 6, 12, and 13; IEC IP67
PVC-jacketed 5-conductor 2 m or 9 m unterminated cable, or 5-pin Euro-style quick-disconnect (QD) fitting are
available. QD cables are ordered separately. See page 382.
Temperature: -20° to +70° C
The first condition presented during TEACH mode becomes the output ON condition.
DC11 (p. 478)
MINI-BEAM
ON when power is applied
Flashes when received light level approaches the switching threshold
OFF when no signal is received.
Pulses to indicate signal strength (received light level). Rate is proportional to signal
strength (the stronger the signal, the faster the pulse rate). This is a function of Banner’s
Alignment Indicating Device (AID).
OFF to indicate sensor is ready to learn output OFF condition
ON when outputs are conducting
®
Expert
More information online at
Relative humidity: 90% at 50° C (non-condensing)
™
Specifications
MINI-BEAM
bannerengineering.com
®
Expert
Compact Sensors
™
Series
83