AD9627-125EBZ Analog Devices Inc, AD9627-125EBZ Datasheet - Page 51

• Manufacturer Part Number: AD9627-125EBZ
• Description: 12Bit 125 Msps Dual 1.8V PB Free ADC
• Manufacturer: Analog Devices Inc

Specifications of AD9627-125EBZ

• Number Of Adc's: 2
• Number Of Bits: 12
• Sampling Rate (per Second): 125M
• Data Interface: Serial
• Inputs Per Adc: 1 Differential
• Input Range: 2 Vpp
• Power (typ) @ Conditions: 900mW @ 125MSPS
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: AD9627
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

EVALUATION BOARD
The AD9627 evaluation board provides all of the support circuitry
required to operate the ADC in its various modes and configura-
tions. The converter can be driven differentially through a double
balun configuration (default) or optionally through the AD8352
differential driver. The ADC can also be driven in a single-ended
fashion. Separate power pins are provided to isolate the DUT
from the
be selected by proper connection of various components (see
Figure 75 to Figure 92). Figure 74 shows the typical bench
characterization setup used to evaluate the ac performance of
the AD9627.
It is critical that the signal sources used for the analog input and
clock have very low phase noise (<<1 ps rms jitter) to realize the
optimum performance of the converter. Proper filtering of the
analog input signal to remove harmonics and lower the integrated
or broadband noise at the input is also necessary to achieve the
specified noise performance.
See Figure 75 to Figure 79 for the complete schematics and
layout diagrams that demonstrate the routing and grounding
techniques that should be applied at the system level.
POWER SUPPLIES
This evaluation board comes with a wall-mountable switching
power supply that provides a 6 V, 2 A maximum output. Connect
the supply to the rated 100 V ac to 240 V ac wall outlet at 47 Hz
to 63 Hz. The output of the supply is a 2.1 mm inner diameter
circular jack that connects to the PCB at J16. Once on the PC
board, the 6 V supply is fused and conditioned before connection
to six low dropout linear regulators that supply the proper bias
to each of the various sections on the board.
WALL OUTLET
100V TO 240V AC
47Hz TO 63Hz
AD8352
ROHDE & SCHWARZ,
ROHDE & SCHWARZ,
ROHDE & SCHWARZ,
2V p-p SIGNAL
2V p-p SIGNAL
2V p-p SIGNAL
SYNTHESIZER
SYNTHESIZER
SYNTHESIZER
SMA100A,
SMA100A,
SMA100A,
drive circuitry. Each input configuration can
SWITCHING
SUPPLY
POWER
BAND-PASS
BAND-PASS
FILTER
FILTER
2A MAX
6V DC
AINA
AINB
CLK
–
5.0V
+
Figure 74. Evaluation Board Connection
–
1.8V
EVALUATION BOARD
+
Rev. B | Page 51 of 76
AD9627
–
3.3V
+
–
3.3V
External supplies can be used to operate the evaluation board
by removing L1, L3, L4, and L13 to disconnect the voltage
regulators supplied from the switching power supply. This enables
the user to individually bias each section of the board. Use P3
and P4 to connect a different supply for each section. At least
one 1.8 V supply is needed with a 1 A current capability for
AVDD and DVDD; a separate 1.8 V to 3.3 V supply is recom-
mended for DRVDD. To operate the evaluation board using the
AD8352 option, a separate 5.0 V supply (AMP VDD) with
a 1 A current capability is needed. To operate the evaluation board
using the alternate SPI options, a separate 3.3 V analog supply
(VS) is needed, in addition to the other supplies. The 3.3 V
supply (VS) should have a 1 A current capability, as well. Solder
Jumper SJ35 allows the user to separate AVDD and DVDD,
if desired.
INPUT SIGNALS
When connecting the clock and analog source, use clean signal
generators with low phase noise, such as the Rohde & Schwarz
SMA100A signal generators or the equivalent. Use 1 m long,
shielded, RG-58, 50 Ω coaxial cable for making connections to the
evaluation board. Enter the desired frequency and amplitude for
the ADC. The AD9627 evaluation board from Analog Devices,
Inc., can accept a ~2.8 V p-p or 13 dBm sine wave input for the
clock. When connecting the analog input source, it is recom-
mended that a multipole, narrow-band, band-pass filter with 50 Ω
terminations be used. Band-pass filters of this type are available
from TTE, Allen Avionics, and K&L Microwave, Inc. Connect the
filter directly to the evaluation board, if possible.
OUTPUT SIGNALS
The parallel CMOS outputs interface directly with the Analog
Devices standard ADC data capture board (HSC-ADC-EVALCZ).
For more information on the ADC data capture boards and their
optional settings, visit www.analog.com/FIFO.
+
PARALLEL
PARALLEL
–
3.3V
12-BIT
12-BIT
CMOS
CMOS
+
SPI
HSC-ADC-EVALCZ
CAPTURE BOARD
FPGA BASED
CONNECTION
DATA
SPI
USB
VISUAL ANALOG
CONTROLLER
PC RUNNING
SOFTWARE
AND SPI
AD9627