AD1847JP Analog Devices Inc, AD1847JP Datasheet - Page 6

• Manufacturer Part Number: AD1847JP
• Manufacturer: Analog Devices Inc

Specifications of AD1847JP

• Single Supply Voltage (typ): 5V
• Single Supply Voltage (min): 4.75V
• Single Supply Voltage (max): 5.25V
• Package Type: PLCC
• Lead Free Status / RoHS Status: Not Compliant

AD1847
PIN DESCRIPTIONS
Parallel Interface
Pin Name
SCLK
SDFS
SDI
SDO
RESET
PWRDOWN
BM
TSO
TSI
CLKOUT
Analog Signals
Pin Name
L_LINE1
R_LINE1
L_LINE2
R_LINE2
L_AUX1
R_AUX1
L_AUX2
R_AUX2
L_OUT
R_OUT
PLCC
23
17
22
18
26
27
32
31
30
28
PLCC TQFP
1
6
4
5
11
12
33
7
8
44
39
44
42
43
5
6
27
1
2
38
17
11
16
12
20
21
26
25
24
22
TQFP
I/O
O
O
O
I/O
I/O
I
I
I
I
I
I/O
I
I
I
I
I
I
I
I
O
O
Description
Serial Clock. SCLK is a bidirectional signal that supplies the clock as an output to the
serial bus when the Bus Master (BM) pin is driven HI and accepts the clock as an input
when the BM pin is driven LO. The serial clock output is fixed at 12.288 MHz when
XTAL1 is selected, and 11.2896 MHz when XTAL2 is selected. SCLK runs continu-
ously. An AD1847 should always be configured as the serial bus master unless it is a slave
in a daisy-chained multiple codec system.
Serial Data Frame Sync. SDFS is a bidirectional signal that supplies the frame synchroni-
zation signal as an output to the serial bus when the Bus Master (BM) pin is driven HI
and accepts the frame synchronization signal as an input when the BM pin is driven LO.
The SDFS frequency powers up at one half of the AD1847 sample rate (i.e., FRS bit = 0)
with two samples per frame and can be programmed to match the sample rate (i.e., FRS
bit = 1) with one sample per frame. An AD1847 should always be configured as the serial
bus master unless it is a slave in a daisy-chained multiple codec system.
Serial Data Input. SDI is used by peripheral devices such as the host CPU or a DSP to
supply control and playback data information to the AD1847. All control and playback
transfers are 16 bits long, MSB first.
Serial Data Output. SDO is used to supply status/index readback and capture data infor-
mation to peripheral devices such as the host CPU or a DSP. All status/index readback
and capture data transfers are 16 bits long, MSB first. Three-state output driver.
Reset. The RESET signal is active LO. The assertion of this signal will initialize the
on-chip registers to their default values. See the “Control Register Definitions” section for
a description of the contents of the control registers after RESET is deasserted.
Powerdown. The PWRDOWN signal is active LO. The assertion of this signal will reset
the on-chip control registers (identically to the RESET signal) and will also place the
AD1847 in a low power consumption mode. V
Bus Master. The assertion (HI) of this signal indicates that the AD1847 is the serial bus
master. The AD1847 will then supply the serial clock (SCLK) and the frame sync (SDFS)
signals for the serial bus. One and only one AD1847 should always be configured as the
serial bus master. If BM is connected to logic LO, the AD1847 is configured as a bus
slave, and will accept the SCLK and SDFS signals as inputs. An AD1847 should only be
configured as a serial bus slave when an AD1847 serial bus master already exists, in
daisy-chained multiple codec systems.
Time Slot Output. This signal is asserted HI by the AD1847 coincidentally with the LSB
of the last time slot used by the AD1847. Used in daisy-chained multiple codec systems.
Time Slot Input. The assertion of this signal indicates that the AD1847 should immedi-
ately use the next three time slots (TSSEL = 1) or the next six time slots (TSSEL = 0)
and then activate the TSO pin to enable the next device down the TDM chain. TSI
should be driven LO when the AD1847 is the bus master or in single codec systems. Used
in daisy-chained multiple codec systems.
Clock Output. This signal is the buffered version of the crystal clock output and the fre-
quency is dependent on which crystal is selected. This pin can be three-stated by driving
the BM pin LO or by programming the CLKTS bit in the Pin Control Register. See the
“Control Registers” section for more details. The CLKOUT frequency is 12.288 MHz
when XTAL1 is selected and 16.9344 MHz when XTAL2 is selected.
Description
Left Line Input #1. Line level input for the #1 left channel.
Right Line Input #1. Line level input for the #1 right channel.
Left Line Input #2. Line level input for the #2 left channel.
Right Line Input #2. Line level input for the #2 right channel.
Left Auxiliary Input #1. Line level input for the AUX1 left channel.
Right Auxiliary Input #1. Line level input for the AUX1 right channel.
Left Auxiliary Input #2. Line level input for the AUX2 left channel.
Right Auxiliary Input #2. Line level input for the AUX2 right channel.
Left Line Output. Line level output for the left channel.
Right Line Output. Line level output for the right channel.
–6–
REF
and all analog circuitry are disabled.
REV. B