MT16JSS51264HY-1G1A1 Micron Technology Inc, MT16JSS51264HY-1G1A1 Datasheet - Page 10

• Manufacturer Part Number: MT16JSS51264HY-1G1A1
• Manufacturer: Micron Technology Inc

Specifications of MT16JSS51264HY-1G1A1

• Main Category: DRAM Module
• Sub-category: DDR3 SDRAM
• Module Type: 204SODIMM
• Device Core Size: 64b
• Organization: 512Mx64
• Total Density: 4GByte
• Maximum Clock Rate: 1.066GHz
• Operating Supply Voltage (typ): 1.5V
• Operating Current: 2.24A
• Number Of Elements: 16
• Operating Supply Voltage (max): 1.575V
• Operating Supply Voltage (min): 1.425V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Pin Count: 204
• Mounting: Socket
• Lead Free Status / RoHS Status: Compliant

Temperature Sensor with Serial Presence-Detect EEPROM
Table 10:
Table 11:
EVENT# Pin
PDF: 09005aef832ed836/Source: 09005aef832ed8fb
JSS16C512x64H.fm - Rev. B 12/08 EN
Parameter/Condition
Parameter/Condition
Supply voltage
Supply current: Vdd = 3.3V
Input high voltage: Logic 1; SCL, SDA
Input low voltage: Logic 0; SCL, SDA
Output low voltage: Iout = 2.1mA
Input current
Temperature sensing range
Temperature sensor accuracy (initial release)
Temperature sensor accuracy (class B)
Time bus must be free before a new transition can start
SDA fall time
SDA rise time
Data hold time
Start condition hold time
Clock HIGH period
Clock LOW period
SCL clock frequency
Data setup time
Start condition setup time
Stop condition setup time
Temperature Sensor with Serial Presence-Detect EEPROM Operating Conditions
Sensor and EEPROM Serial Interface Timing
The temperature sensor continuously monitors the module’s temperature and can be
read back at any time over the I
The temperature sensor also adds the EVENT# pin (open drain). Not used by the SPD
EEPROM, EVENT# is a temperature sensor output used to flag critical events that can be
set up in the sensor’s configuration register.
EVENT# has three defined modes of operation: interrupt mode, compare mode, and
critical temperature mode. The open-drain output of EVENT# under the three separate
operating modes is illustrated in Figure 3 on page 11. Event thresholds are programmed
in the 0x01 register using a hysteresis. The alarm window provides a comparison
window, with upper and lower limits set in the alarm upper boundary register and the
alarm lower boundary register, respectively. When the alarm window is enabled,
EVENT# will trigger whenever the temperature is outside the MIN or MAX values set by
the user.
The interrupt mode enables software to reset EVENT# after a critical temperature
threshold has been detected. Threshold points are set in the configuration register by the
user. This mode triggers the critical temperature limit and both the MIN and MAX of the
temperature window.
4GB (x64, DR): 204-Pin DDR3 SDRAM SODIMM
10
2
C bus shared with the SPD EEPROM.
t
Symbol
Symbol
t
t
Vddspd
t
HD:DAT
SU:DAT
t
SU:STO
SU:STA
t
t
H:STA
Micron Technology, Inc., reserves the right to change products or specifications without notice.
t
HIGH
LOW
f
Idd
Vih
Vol
BUF
SCL
Vil
Iin
t
t
–
–
–
R
F
+1.45
Min
+3.0
Min
–5.0
–2.0
–1.0
–40
200
250
4.7
4.0
4.0
4.7
4.7
4.0
20
10
–
–
–
–
Electrical Specifications
©2008 Micron Technology, Inc. All rights reserved.
Vddspd + 1
+0.55
+125
Max
Max
1000
+3.6
+2.0
+0.4
+5.0
+2.0
+1.0
300
900
100
50
–
–
–
–
–
–
Units
Units
kHz
mA
µA
°C
°C
°C
µs
ns
ns
ns
µs
µs
µs
ns
µs
µs
V
V
V
V