CP82C37A-5 Intersil, CP82C37A-5 Datasheet - Page 3

• Manufacturer Part Number: CP82C37A-5
• Manufacturer: Intersil

Specifications of CP82C37A-5

• Operating Temperature (max): 70C
• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Lead Free Status / RoHS Status: Not Compliant

Pin Description
SYMBOL
DB0-DB7
DREQ0-
READY
DREQ3
RESET
HLDA
GND
V
CLK
IOW
IOR
CS
CC
NUMBER
16-19
21-23
26-30
PIN
31
20
12
11
13
6
7
1
2
TYPE
3
I/O
I/O
I/O
I
I
I
I
I
I
V
decoupling.
Ground
CLOCK INPUT: The Clock Input is used to generate the timing signals which control 82C37A
operations. This input may be driven from DC to 12.5MHz for the 82C37A-12, from DC to 8MHz for
the 82C37A, or from DC to 5MHz for the 82C37A-5. The Clock may be stopped in either state for
standby operation.
CHIP SELECT: Chip Select is an active low input used to enable the controller onto the data bus for
CPU communications.
RESET: This is an active high input which clears the Command, Status, Request, and Temporary
registers, the First/Last Flip-Flop, and the mode register counter. The Mask register is set to ignore
requests. Following a Reset, the controller is in an idle cycle.
READY: This signal can be used to extend the memory read and write pulses from the 82C37A to
accommodate slow memories or I/O devices. READY must not make transitions during its specified
set-up and hold times. See Figure 12 for timing. READY is ignored in verify transfer mode.
HOLD ACKNOWLEDGE: The active high Hold Acknowledge from the CPU indicates that it has
relinquished control of the system busses. HLDA is a synchronous input and must not transition
during its specified set-up time. There is an implied hold time (HLDA inactive) of TCH from the rising
edge of CLK, during which time HLDA must not transition.
DMA REQUEST: The DMA Request (DREQ) lines are individual asynchronous channel request
inputs used by peripheral circuits to obtain DMA service. In Fixed Priority, DREQ0 has the highest
priority and DREQ3 has the lowest priority. A request is generated by activating the DREQ line of a
channel. DACK will acknowledge the recognition of a DREQ signal. Polarity of DREQ is
programmable. RESET initializes these lines to active high. DREQ must be maintained until the
corresponding DACK goes active. DREQ will not be recognized while the clock is stopped. Unused
DREQ inputs should be pulled High or Low (inactive) and the corresponding mask bit set.
DATA BUS: The Data Bus lines are bidirectional three-state signals connected to the system data
bus. The outputs are enabled in the Program condition during the I/O Read to output the contents
of a register to the CPU. The outputs are disabled and the inputs are read during an I/O Write cycle
when the CPU is programming the 82C37A control registers. During DMA cycles, the most
significant 8-bits of the address are output onto the data bus to be strobed into an external latch by
ADSTB. In memory-to-memory operations, data from the memory enters the 82C37A on the data
bus during the read-from-memory transfer, then during the write-to-memory transfer, the data bus
outputs write the data into the new memory location.
I/O READ: I/O Read is a bidirectional active low three-state line. In the Idle cycle, it is an input
control signal used by the CPU to read the control registers. In the Active cycle, it is an output control
signal used by the 82C37A to access data from the peripheral during a DMA Write transfer.
I/O WRITE: I/O Write is a bidirectional active low three-state line. In the Idle cycle, it is an input
control signal used by the CPU to load information into the 82C37A. In the Active cycle, it is an output
control signal used by the 82C37A to load data to the peripheral during a DMA Read transfer.
CC
: is the +5V power supply pin. A 0.1µF capacitor between pins 31 and 20 is recommended for
82C37A
82C37A
DESCRIPTION
March 20, 2006
FN2967.2