MC9S12XDP512CAL Freescale, MC9S12XDP512CAL Datasheet - Page 591

• Manufacturer Part Number: MC9S12XDP512CAL
• Manufacturer: Freescale

Specifications of MC9S12XDP512CAL

• Cpu Family: HCS12
• Device Core Size: 16b
• Frequency (max): 40MHz
• Interface Type: CAN/I2C/SCI/SPI
• Total Internal Ram Size: 32KB
• # I/os (max): 91
• Number Of Timers - General Purpose: 12
• Operating Supply Voltage (typ): 2.5/5V
• Operating Supply Voltage (max): 2.75/5.5V
• Operating Supply Voltage (min): 2.35/3.15V
• On-chip Adc: 2(16-chx10-bit)
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 112
• Package Type: LQFP
• Program Memory Type: Flash
• Program Memory Size: 512KB
• Lead Free Status / RoHS Status: Compliant

The ACK_ENABLE sends an ACK pulse when the command has been completed. This feature could be
used by the host to evaluate if the target supports the hardware handshake protocol. If an ACK pulse is
issued in response to this command, the host knows that the target supports the hardware handshake
protocol. If the target does not support the hardware handshake protocol the ACK pulse is not issued. In
this case, the ACK_ENABLE command is ignored by the target since it is not recognized as a valid
command.
The BACKGROUND command will issue an ACK pulse when the CPU changes from normal to
background mode. The ACK pulse related to this command could be aborted using the SYNC command.
The GO command will issue an ACK pulse when the CPU exits from background mode. The ACK pulse
related to this command could be aborted using the SYNC command.
The GO_UNTIL command is equivalent to a GO command with exception that the ACK pulse, in this
case, is issued when the CPU enters into background mode. This command is an alternative to the GO
command and should be used when the host wants to trace if a breakpoint match occurs and causes the
CPU to enter active background mode. Note that the ACK is issued whenever the CPU enters BDM, which
could be caused by a breakpoint match or by a BGND instruction being executed. The ACK pulse related
to this command could be aborted using the SYNC command.
The TRACE1 command has the related ACK pulse issued when the CPU enters background active mode
after one instruction of the application program is executed. The ACK pulse related to this command could
be aborted using the SYNC command.
15.4.9
The SYNC command is unlike other BDM commands because the host does not necessarily know the
correct communication speed to use for BDM communications until after it has analyzed the response to
the SYNC command. To issue a SYNC command, the host should perform the following steps:
Upon detecting the SYNC request from the host, the target performs the following steps:
The host measures the low time of this 128 cycle SYNC response pulse and determines the correct speed
for subsequent BDM communications. Typically, the host can determine the correct communication speed
Freescale Semiconductor
1. Drive the BKGD pin low for at least 128 cycles at the lowest possible BDM serial communication
2. Drive BKGD high for a brief speedup pulse to get a fast rise time (this speedup pulse is typically
3. Remove all drive to the BKGD pin so it reverts to high impedance.
4. Listen to the BKGD pin for the sync response pulse.
1. Discards any incomplete command received or bit retrieved.
2. Waits for BKGD to return to a logic one.
3. Delays 16 cycles to allow the host to stop driving the high speedup pulse.
4. Drives BKGD low for 128 cycles at the current BDM serial communication frequency.
5. Drives a one-cycle high speedup pulse to force a fast rise time on BKGD.
6. Removes all drive to the BKGD pin so it reverts to high impedance.
frequency (the lowest serial communication frequency is determined by the crystal oscillator or the
clock chosen by CLKSW.)
one cycle of the host clock.)
SYNC — Request Timed Reference Pulse
MC9S12XDP512 Data Sheet, Rev. 2.21
Chapter 15 Background Debug Module (S12XBDMV2)
591