- Components/
- Capacitors/
- Ceramic/
DE1E3KX472MA5BA01

DE1E3KX472MA5BA01 | |
---|---|
Manufacturer Part Number | DE1E3KX472MA5BA01 |
Description | Cap Ceramic 0.0047uF 250VAC E 20% 15 X 8mm RDL 10mm Bulk |
Manufacturer | Murata Electronics |
Type | Radial |
DE1E3KX472MA5BA01 datasheet |
|
Specifications of DE1E3KX472MA5BA01 | |||
---|---|---|---|
Package/case | 15(Max) X 8(Max) | Lead Pitch For Radial | 10 mm |
Capacitance Value | 0.0047 uF | Dielectric | E |
Tolerance | 20 % | Voltage | 250 Vac |
Product Depth | 8(Max) mm |
PrevNext
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
DEJ Series Specifications and Test Methods
Continued from the preceding page.
No.
Item
Appearance
I.R.
Soldering
10
Effect
Dielectric
(Non-Preheat)
Strength
Appearance
I.R.
5
Soldering
11
Effect
Dielectric
(On-Preheat)
Strength
Appearance
Capacitance
Vibration
12
Resistance
D.F.
Solvent
13
Appearance
Resistance
Appearance
Capacitance
Change
Humidity
(Under
14
Steady
D.F.
State)
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Humidity
15
Insulation
D.F.
I.R.
Dielectric
Strength
*
1
"room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
18
Specifications
No marked defect
1000MΩ min.
Per Item 6
No marked defect
1000MΩ min.
Per Item 6
No marked defect
Within the specified tolerance
Char.
Specifications
D.F.V2.5%
E
D.F.V5.0%
F
No marked defect
No marked defect
Char.
Capacitance Change
E
Within ±20%
F
Within ±30%
Char.
Specifications
E
D.F.V5.0%
D.F.V7.5%
F
1000MΩ min.
Per Item 6
No marked defect
Char.
Capacitance Change
E
Within ±20%
F
Within ±30%
Char.
Specifications
D.F.V5.0%
E
D.F.V7.5%
F
1000MΩ min.
Per Item 6
Test Method
As shown in figure, the lead wires
Thermal
should be immersed in solder of
Screen
350±10˚C up to 1.5 to 2.0mm from
the root of terminal for 3.5±0.5 sec.
Pre-treatment:
Capacitor should be stored at
85±2˚C for 1 hr., then placed at room condition*
before initial measurements.
Post-treatment:
Capacitor should be stored for 4 to 24 hrs. at
room condition*
1
.
First the capacitor should be
Thermal
stored at 120+0/-5°C for
Screen
60+0/-5 sec.
Then, as in figure, the lead wires
should be immersed in solder of
260+0/-5°C up to 1.5 to 2.0mm
from the root of terminal for
7.5+0/-1 sec.
Pre-treatment:
Capacitor should be stored at 85±2˚C for 1 hr., then placed at
room condition*
1
for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 4 to 24 hrs. at
room condition*
1
.
The capacitor should be firmly soldered to the supporting lead
wire and vibrated at a frequency range of 10 to 55Hz, 1.5mm in
total amplitude, with about a 1 minute rate of vibration change
from 10Hz to 55Hz and back to 10Hz.
Apply for a total of 6 hrs., 2 hrs. each in 3 mutually perpendicular
directions.
The capacitor should be immersed into a isopropyl alcohol for
30±5 sec.
Set the capacitor for 500±12 hrs. at 40±2˚C in 90 to 95%
relative humidity.
Pre-treatment:
Capacitor should be stored at 85±2˚C for 1 hr., then placed at
room condition*
1
for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition*
The capacitor should be subjected to 40±2˚C, relative humidity
of 90 to 98% for 8 hrs., and then removed in room temperature
for 16 hrs. until 5 cycles.
Pre-treatment:
Capacitor should be stored at 85±2˚C for 1 hr., then placed at
room condition*
1
for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 1 to 2 hrs. at room condition*
Continued on the following page.
C85E.pdf
08.10.29
Capacitor
1.5
to 2.0mm
Molten
Solder
1
for 24±2 hrs.
Capacitor
1.5
to 2.0mm
Molten
Solder
1
.
1
.
Related parts for DE1E3KX472MA5BA01 | ||||
---|---|---|---|---|
Part Number | Description | Manufacturer | Datasheet | Request |
![]() |
BUZZER PIEZO 25VP-P SMD | Murata Electronics North America | ||
![]() |
CAP 4-ARRAY 680PF 100V X7R 1206 | Murata Electronics North America |
| |
![]() |
CAP 4-ARRAY 1000PF 100V X7R 1206 | Murata Electronics North America |
| |
![]() |
CAP 4-ARRAY 1800PF 100V X7R 1206 | Murata Electronics North America |
| |
![]() |
CAP 4-ARRAY 68000PF 16V X7R 1206 | Murata Electronics North America |
| |
![]() |
CAP CER 1000PF 50V 10% X7R 0402 | Murata Electronics North America |
| |
![]() |
CAP CER 10000PF 16V 10% X7R 0402 | Murata Electronics North America |
| |
![]() |
CAP 5.5-25PF 2.5X3.2MM SMD | Murata Electronics North America |
| |
![]() |
CAP 4.5-20PF 2.5X3.2MM SMD | Murata Electronics North America |
| |
![]() |
CAP 5.0-20PF 3.2X4.5MM SMD RED | Murata Electronics North America |
| |
![]() |
CAP 2.0-6.0PF 3.2X4.5MM SMD BLU | Murata Electronics North America |
| |
![]() |
CAP 1.4-3.0PF 3.2X4.5MM SMD BRN | Murata Electronics North America |
| |
![]() |
CAP 3.0-10PF 3.2X4.5MM SMD WHT | Murata Electronics North America |
| |
![]() |
CAP 2.0-6.0PF 4X4.5MM TOPADJ BLU | Murata Electronics North America |
| |
![]() |
CAP 8.5-40PF 4X4.5MM TOPADJ YEL | Murata Electronics North America |
|