DE1E3KX472MA5BA01

Manufacturer Part NumberDE1E3KX472MA5BA01
DescriptionCap Ceramic 0.0047uF 250VAC E 20% 15 X 8mm RDL 10mm Bulk
ManufacturerMurata Electronics
TypeRadial
DE1E3KX472MA5BA01 datasheet
 


Specifications of DE1E3KX472MA5BA01

Package/case15(Max) X 8(Max)Lead Pitch For Radial10 mm
Capacitance Value0.0047 uFDielectricE
Tolerance20 %Voltage250 Vac
Product Depth8(Max) mm  
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Page 31
32
Page 32
33
Page 33
34
Page 34
35
Page 35
36
Page 36
37
Page 37
38
Page 38
39
Page 39
40
Page 40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
Page 34/72

Download datasheet (2Mb)Embed
PrevNext
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
DES Series Specifications and Test Methods
Continued from the preceding page.
No.
Item
Appearance
Capacitance
Change
Soldering Effect
13
(On-Preheat)
Dielectric Strength
(Between Lead
Wires)
Appearance
Capacitance
Change
D.F.
I.R.
Temperature
14
Cycle
6
Dielectric Strength
(Between Lead
Wires)
Appearance
Capacitance
Change
Humidity (Under
15
Steady State)
D.F.
I.R.
Appearance
Capacitance
Humidity
Change
16
Loading
D.F.
I.R.
Appearance
Capacitance
Change
D.F.
17 Life
I.R.
* "room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
32
Specifications
No marked defect
First the capacitor should be
stored at 120+0/-5°C for
Within ±10%
60+0/-5 sec.
Then, as in figure, the lead wires
should be immersed in solder of
260+0/-5°C up to 1.5 to 2.0mm
from the root of terminal for
7.5+0/-1 sec.
Per item 4.
Pre-treatment:
Capacitor should be stored at 125±3°C for 1 hr., then placed
at room condition* for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 24±2 hrs. at room condition*.
No marked defect
The capacitor should be subjected to 5 temperature cycles.
<Temperature Cycle>
Within ±10%
0.4% max.
1000MΩ min.
Pre-treatment:
Capacitor should be stored at 125±3°C for 1 hr., then placed
Per item 4.
at room condition* for 24±2 hrs. before initial measurements.
Post-treatment:
Capacitor should be stored for 24±2 hrs. at room condition*.
No marked defect
Set the capacitor for 500+24/-0 hrs. at 40±2°C in 90 to 95%
relative humidity.
Within ±10%
Pre-treatment:
Capacitor should be stored at 125±3°C for 1 hr., then placed
0.4% max.
at room condition* for 24±2 hrs. before initial measurements.
Post-treatment:
1000MΩ min.
Capacitor should be stored for 1 to 2 hrs. at room condition*.
No marked defect
Apply the rated voltage for 500+24/-0 hrs. at 40±2°C in 90 to
95% relative humidity. (Charge/Discharge currentV50mA)
Within ±10%
Pre-treatment:
Capacitor should be stored at 125±3°C for 1 hr., then placed
0.6% max.
at room condition* for 24±2 hrs. before initial measurements.
Post-treatment:
1000MΩ min.
Capacitor should be stored for 1 to 2 hrs. at room condition*.
No marked defect
Apply a DC voltage of 200% of the rated voltage (DC500V) or
DC voltage of 150% of the rated voltage (DC1kV) for 1000
Within ±10%
+48/-0 hrs. at 125±2°C with a relative humidity of 50% max.
(Charge/Discharge currentV50mA)
0.4% max.
Pre-treatment:
Capacitor should be stored at 125±3°C for 1 hr., then placed
at room condition* for 24±2 hrs. before initial measurements.
Post-treatment:
2000MΩ min.
Capacitor should be stored at 125±3°C for 1 hr., then placed
at room condition* for 24±2 hrs.
C85E.pdf
08.10.29
Test Method
Capacitor
Thermal
Screen
1.5
to 2.0mm
Molten
Solder
Step
Temperature (°C)
Time (min)
1
-25±3
30
2
Room Temp.
3
3
125±3
30
4
Room Temp.
3
Cycle time: 5 cycle