STM8L152C8 STMicroelectronics, STM8L152C8 Datasheet - Page 36

• Manufacturer Part Number: STM8L152C8
• Description: STM8L-Ultra Low Power-8 bits Microcontrollers
• Manufacturer: STMicroelectronics

Specifications of STM8L152C8

• Operating Power Supply: 1.65 to 3.6 V (without BOR), 1.8 to 3.6 V (with BOR)
• Temp. Range: −40 to 85, 105 or 125 °C
• 5 Low Power Modes: Wait, Low power run (5.9 μA), Low power wait (3 μA), Active-halt with full RTC (1.4 μA), Halt (400 nA)
• Dynamic Power Consumption: 200 μA/MHz+330 μA
• Ultra Low Leakage Per I/0: 50 nA
• Max Freq: 16 MHz, 16 CISC MIPS peak
• Lcd: 8x40 or 4x44 w/ step-up converter

Pin description
Table 5.
1. At power-up, the PA1/NRST pin is a reset input pin with pull-up. To be used as a general purpose pin (PA1), it can be
2. [ ] Alternate function remapping option (if the same alternate function is shown twice, it indicates an exclusive choice not a
3. Available on STM8L152xx devices only.
4. A pull-up is applied to PB0 and PB4 during the reset phase. These two pins are input floating after reset release.
5. In the 5 V tolerant I/Os, the protection diode to V
6. In the open-drain output column, ‘T’ defines a true open-drain I/O (P-buffer, weak pull-up and protection diode to V
7. Available on STM8L152xx devices only. On STM8L151xx devices it is reserved and must be tied to V
8. The PA0 pin is in input pull-up during the reset phase and after reset release.
9. High Sink LED driver capability available on PA0.
36/126
13 9
37 29
38 30
68 56 40 V
67 55 39 V
48
47
5
number
configured only as output open-drain or push-pull, not as a general purpose input. Refer to Section Configuring NRST/PA1
pin as general purpose output in the STM8L15xx and STM8L16xx reference manual (RM0031).
duplication of the function).
not implemented).
Pin
1
-
-
1
- V
- V
- V
- V
- V
PA0
SWIM/BEEP/IR_TIM
High density and medium+ density STM8L15x pin description (continued)
System configuration options
As shown in
alternate functions can be remapped on different I/O ports by programming one of the two
remapping registers described in the “Routing interface (RI) and system configuration
controller” section in the STM8L15xx and STM8L16xx reference manual (RM0031).
SSA/
DD3
SS3
SS2
DD2
SS4
DD4
(8)
V
/[USART1_CK]
REF-
Pin name
Table 5: High density and medium+ density STM8L15x pin
(2)
(9)
/
I/O
S
S
S
DD
Doc ID 17943 Rev 4
is not implemented.
X
Input
X
X HS X
Output
X Port A0
Analog ground voltage /
ADC1 negative voltage reference
IOs supply voltage
IOs ground voltage
IOs ground voltage
IOs supply voltage
IOs ground voltage
IOs supply voltage
STM8L15xx8, STM8L15xR6
[USART1 synchronous
clock]
output /
Beep output / Infrared Timer
output
Default alternate function
(2)
DD
description, some
/ SWIM input and
.
DD
are