STM8L152C8 STMicroelectronics, STM8L152C8 Datasheet - Page 85

• Manufacturer Part Number: STM8L152C8
• Description: STM8L-Ultra Low Power-8 bits Microcontrollers
• Manufacturer: STMicroelectronics

Specifications of STM8L152C8

• Operating Power Supply: 1.65 to 3.6 V (without BOR), 1.8 to 3.6 V (with BOR)
• Temp. Range: −40 to 85, 105 or 125 °C
• 5 Low Power Modes: Wait, Low power run (5.9 μA), Low power wait (3 μA), Active-halt with full RTC (1.4 μA), Halt (400 nA)
• Dynamic Power Consumption: 200 μA/MHz+330 μA
• Ultra Low Leakage Per I/0: 50 nA
• Max Freq: 16 MHz, 16 CISC MIPS peak
• Lcd: 8x40 or 4x44 w/ step-up converter

STM8L15xx8, STM8L15xR6
Table 27.
1. Data based on a differential I
2. Data based on a differential I
3. Peripherals listed above the I
4. Data based on a differential I
I
I
I
I
CPU is in Wait mode in both cases. No IC/OC programmed, no I/O pins toggling. Not tested in production.
the on-chip peripheral when clocked and not kept under reset. The CPU is in Wait mode in both cases. No I/O pins
toggling. Not tested in production.
SPI2, I2C1, DMA1, WWDG.
DD(PVD/BOR)
I
I
I
I
DD(USART1)
DD(USART2)
DD(USART3)
DD(COMP1)
DD(COMP2)
I
DD(WWDG)
I
DD(IDWDG)
I
I
I
I
I
Symbol
I
I
I
DD(DMA1)
I
DD(ADC1)
I
I
DD(TIM1)
DD(TIM2)
DD(TIM3)
DD(TIM5)
DD(TIM4)
DD(SPI1)
DD(SPI2)
DD(I2C1)
DD(DAC)
DD(BOR)
DD(ALL)
Current consumption of on-chip peripherals
Peripheral current consumption
TIM1 supply current
TIM2 supply current
TIM3 supply current
TIM5 supply current
TIM4 timer supply current
USART1 supply current
USART2 supply current
USART3 supply current
SPI1 supply current
SPI2 supply current
I
DMA1 supply current
WWDG supply current
Peripherals ON
ADC1 supply current
DAC supply current
Comparator 1 supply current
Comparator 2 supply current
Power voltage detector and brownout Reset unit supply current
(7)
Brownout Reset unit supply current
Independent watchdog supply current
2
C1 supply current
DD
DD
DD
DD(ALL)
measurement between all peripherals OFF and a timer counter running at 16 MHz. The
measurement between the on-chip peripheral in reset configuration and not clocked and
measurement between ADC in reset configuration and continuous ADC conversion.
(3)
parameter ON: TIM1, TIM2, TIM3, TIM4, TIM5, USART1, USART2, USART3, SPI1,
(5)
(1)
(2)
(2)
(2)
(1)
(1)
(1)
(4)
(2)
(2)
(2)
(2)
(2)
Parameter
(1)
(6)
(6)
Doc ID 17943 Rev 4
(7)
Slow mode
Fast mode
including LSI supply
current
excluding LSI
supply current
V
DD
0.160
1500
Typ.
0.45
0.05
370
2.6
2.4
= 3.0 V
10
63
Electrical parameters
7
7
7
3
5
5
5
3
3
4
3
1
2
5
µA/MHz
Unit
µA
85/126