TMPM363F10FG Toshiba, TMPM363F10FG Datasheet - Page 81

• Manufacturer Part Number: TMPM363F10FG
• Manufacturer: Toshiba

Specifications of TMPM363F10FG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 1024K
• Rom Type: Flash
• Ram (kbytes): 64K
• Number Of Pins: 100
• Package: LQFP(14x14)
• Vcc: 3V
• Cpu Mhz: 64
• Ssp (ch) Spi: 1
• I2c/sio (ch): 4
• Uart/sio (ch): 5
• Usb: Host
• Can: 1
• Ethernet: -
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 2
• 10-bit Da Converter: 8
• 10-bit Ad Converter: 8
• 12-bit Ad Converter: -
• 16-bit Timer / Counter: 16
• Motor / Igbt Control: -
• Real Time Clock: Y
• Watchdog Timer: Y
• Osc Freq Detect: -
• Clock Gear: Y
• Low-power Hold Function: Y
• Remote Control Interface: Y
• Hardware Cec Controller: Y
• Comparators: -
• Low-voltage Detector: -
• Etm Hardware Trace: 4-bit

6.6.8
warm-up counter is activated automatically. And then the system clock output is started after the elapse of con-
figured warm-up time. It is necessary to select a oscillator to be used for warm-up in the CGOSCCR<WU-
PSEL> and to set a warm-up time in the CGOSCCR<WUPT><WUPTL> before executing the instruction to en-
ter the STOP / IDLE1 / SLEEP mode.
tor to stabilize if the low-speed clock is disabled. Enable the low-speed clock and then activate the warm-up
by software.
clock and then activate the warm-up.
Warm-up
Mode transition may require the warm-up so that the internal oscillator provides stable oscillation.
In the mode transition from STOP to the NORMAL / SLOW or from IDLE1 / SLEEP to NORMAL, the
In the transition from NORMAL to SLOW / SLEEP, the warm-up is required so that the internal oscilla-
In the transition from SLOW to NORMAL when the high-speed clock is disabled, enable the high-speed
Table 6-9 shows whether the warm-up setting of each mode transition is required or not.
Note:In STOP / SLEEP modes, the PLL is disabled. When returning from these mode, configure the warm-
up time in consideration of the stability time of the PLL and the internal oscillator. It takes approximate-
ly 200μs for the PLL to be stabilized.
Table 6-9 Warm-up setting in mode transition
NORMAL → IDLE2, 1
NORMAL → SLEEP
NORMAL → SLOW
NORMAL → STOP
NORMAL → BACKUP SLEEP
NORMAL → BACKUP STOP
SLOW → NORMAL
SLOW → SLEEP
SLOW → STOP
SLOW → BACKUP SLEEP
SLOW → BACKUP STOP
IDLE2 → NORMAL
IDLE1 → NORMAL
SLEEP → NORMAL
SLEEP → SLOW
STOP → NORMAL
STOP → SLOW
BACKUP → SLEEP → NOR-
MAL
Mode transition
Page 55
Low-speed oscillator :Setting value of
High-speed oscillator : Setting value
High-speed oscillator : Setting value
High-speed oscillator : more than
High-speed oscillator : more than
Auto-warm-up (note 3)
Auto-warm-up (note 3)
Not required (note 1)
Not required (note 1)
Not required (note 1)
Not required (note 2)
Warm-up setting
of warm-up time
of warm-up time
Auto-warm-up
Auto-warm-up
Auto-warm-up
warm-up time
Not required
Not required
Not required
Not required
Not required
Not required
Not required
Not required
Not required
100μs
500μs
TMPM363F10FG