ISL96017 Intersil Corporation, ISL96017 Datasheet - Page 3

• Manufacturer Part Number: ISL96017
• Description: 128-Tap DCP / 16kbit EEPROM and I2C Serial Interface
• Manufacturer: Intersil Corporation

Absolute Maximum Ratings
Storage Temperature: . . . . . . . . . . . . . . . . . . . . . . . .-65°C to 150°C
Note: All Voltages with Respect to GND
Voltage at RH, RW, RL: . . . . . . . . . . . . . . . . . . . . . . . GND to VDD
VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 4V
Lead Temperature (Soldering, 10s): . . . . . . . . . . . . . . . . . . . . 300°C
Wiper Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA
ESD (MIL-STD-883B, Method 3014) . . . . . . . . . . . . . . . . . . .>2000V
ESD (Machine Model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>150V
CAUTION: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only; the functional
operation of the device, at these or any other conditions above those listed in the operational sections of this specification, is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Note:
Electrical Specifications
DCP IN VOLTAGE DIVIDER MODE (0V at RL, VCC at RH; measured at RW unloaded)
DNL (Note 2, 5) Differential Non-Linearity
INL (Note 2, 6) Integral Non-Linearity
1.
Voltage at SCL, SDA, WP: . . . . . . . . . . . . . . . . . . . . . -0.3V to 4V
(Note 7, 13)
CH/CW/CL
VDDRamp
(Note 2, 3)
(Note 2, 4)
SYMBOL
(Note 13)
(Note 13)
θ
Tech Brief TB379 for details.
IccdSby
I
FSerror
ZSerror
IccdRd
IccdWr
I
LkgDCP
R
JA
LkgDig
R
t
TC
DCP
Wiper
Total
t
D
is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
V
Standby Current at VDD
Read Current at VDD
Write Current at VDD
Leakage Current at Pins SDA, SCL,
and WP
Leakage Current at RH, RW, RL
VDD Power-Up Ramp Rate
DCP Wiper Response Time
Power-Up Delay
RH, RW, RL Pin Capacitance
Total Resistance
R
Wiper Resistance
DCP Resolution
Full-Scale Error
Zero-Scale Error
Ratiometric Temperature
Coefficient
Total
Tolerance
PARAMETER
3
Over recommended operating conditions unless otherwise stated. All voltages with respect to GND.
Serial interface in standby
Reading with 400kHz at SCL
Writing to EEPROM
Pin voltage from GND to VDD
SCL falling edge of last bit of DCP Data Byte to
wiper change
VDD above 2.6V, to DCP Initial Value Register
recall completed, and I
state
W and U versions, respectively. T
Measured between R
T
V
U option
W option
U option
W option
DCP Register between 10 hex and 6F hex
Monotonic over all tap positions
Pin voltage from GND to VDD
A
DD
= 25°C. Measured between R
= 3.3V @ 25°C. Wiper current = V
ISL96017
TEST CONDITIONS
H
2
Thermal Information
Thermal Resistance (Typical, Note 1)
8 Ld TDFN Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90(°C/W)
Moisture Sensitivity (see Technical Brief TB363). . . . . . . . . .Level 2
Maximum Junction Temperature (Plastic Package). . . . . . . . . .150°C
Recommended Operating Conditions
Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
VDD Voltage for DCP Operation . . . . . . . . . . . . . . . . . . 3.0V to 3.6V
Wiper Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -3mA to 3mA
Power Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5mW
and R
C Interface in standby
L
pins.
H
A
and R
= 25°C.
DD
L
/R
pins.
Total
-0.75
MIN
-10
0.2
-20
-1
-2
-5
-1
7
0
0
(Note 1)
10, 50
TYP
100
1.5
10
±4
-1
-1
1
1
MAX
0.75
300
10
10
20
1
1
5
3
0
0
2
5
1
April 17, 2006
θ
ppm/°C
JA
UNIT
V/ms
FN8243.1
LSB
LSB
LSB
LSB
LSB
LSB
Bits
mA
mA
µA
µA
µA
ms
kΩ
pF
µs
%
Ω