is42s16100-7tli Integrated Silicon Solution, Inc., is42s16100-7tli Datasheet

Page 1

... Integrated Silicon Solution, Inc. — www.issi.com Rev. D 01/28/08 FEBRUARY 2008 DESCRIPTION ISSI ’s 16Mb Synchronous DRAM IS42S16100 is organized as a 524,288-word x 16-bit x 2-bank for improved performance. The synchronous DRAMs achieve high-speed data transfer using pipeline architecture. All inputs and outputs signals refer to the rising edge of the clock input. ...

Page 2

... IS42S16100 PIN CONFIGURATION PACKAGE CODE BALL FBGA (Top View) (10 6.4 mm Body, 0.65 mm Ball Pitch PIN DESCRIPTIONS A0-A10 Row Address Input A0-A7 Column Address Input A11 Bank Select Address DQ0 to DQ15 Data I/O CLK System Clock Input ...

Page 3

... IS42S16100 PIN FUNCTIONS Pin No. Symbol Type A0-A10 Input Pin A11 Input Pin 16 Input Pin CAS 34 CKE Input Pin 35 CLK Input Pin 18 Input Pin DQ0 to DQ Pin 12, 39, 40, 42, 43, DQ15 45, 46, 48, 49 14, 36 LDQM, Input Pin ...

Page 4

... IS42S16100 FUNCTIONAL BLOCK DIAGRAM CLK CKE COMMAND CS DECODER RAS CAS & WE CLOCK MODE A11 GENERATOR REGISTER 11 A10 SELF A9 REFRESH REFRESH A8 CONTROLLER CONTROLLER A7 A6 REFRESH A5 COUNTER ROW ADDRESS LATCH 11 4 MEMORY CELL ROW ARRAY ADDRESS 2048 BUFFER BANK SENSE AMP I/O GATE ...

Page 5

... IS42S16100 ABSOLUTE MAXIMUM RATINGS Symbol Parameters V Maximum Supply Voltage dd max V Maximum Supply Voltage for Output Buffer ddq max V Input Voltage iN V Output Voltage out P Allowable Power Dissipation d max I output Shorted Current cs T operating Temperature opr T Storage Temperature stg DC RECOMMENDED OPERATING CONDITIONS ...

Page 6

... IS42S16100 DC ELECTRICAL CHARACTERISTICS Symbol Parameter i Input Leakage Current il i Output Leakage Current ol V Output High Voltage Level Output Low Voltage Level Operating Current (1,2) cc1 i Precharge Standby Current CKE ≤ V cc2p I (In Power-Down Mode) cc2ps i Active Standby Current cc3N I (In Non Power-Down Mode) ...

Page 7

... IS42S16100 AC CHARACTERISTICS (1,2,3) Symbol Parameter t 3 Clock Cycle Time Access Time From CLK ( CLK HIGH Level Width chi t CLK LOW Level Width Output Data Hold Time Output LOW Impedance Time Output HIGH Impedance Time ...

Page 8

... IS42S16100 OPERATING FREQUENCY / LATENCY RELATIONSHIPS SYMBOL PARAMETER — Clock Cycle Time — Operating Frequency t CAS Latency cac t Active Command To Read/Write Command Delay Time rcd t RAS Latency ( rac rcd cac t Command Period (REF to REF / ACT to ACT Command Period (ACT to PRE) ...

Page 9

... IS42S16100 COMMANDS Active Command CLK CKE HIGH CS RAS CAS WE A0-A9 ROW A10 ROW BANK 1 A11 BANK 0 Write Command CLK HIGH CKE CS RAS CAS WE A0-A9 COLUMN AUTO PRECHARGE A10 NO PRECHARGE BANK 1 A11 BANK 0 Notes: 1. A8-A9 = Don’t Care. Integrated Silicon Solution, Inc. — www.issi.com Rev. D ...

Page 10

... IS42S16100 COMMANDS (cont.) No-Operation Command CLK CKE HIGH CS RAS CAS WE A0-A9 A10 A11 Mode Register Set Command CLK HIGH CKE CS RAS CAS WE A0-A9 OP-CODE A10 OP-CODE A11 OP-CODE 10 Device Deselect Command CLK CKE HIGH CS RAS CAS WE A0-A9 A10 A11 Auto-Refresh Command CLK HIGH CKE ...

Page 11

... IS42S16100 COMMANDS (cont.) Self-Refresh Command CLK CKE CS RAS CAS WE A0-A9 A10 A11 Clock Suspend Command CLK CKE BANK(S) ACTIVE CS NOP RAS NOP CAS NOP WE NOP A0-A9 A10 A11 Integrated Silicon Solution, Inc. — www.issi.com Rev. D 01/28/08 Power Down Command CLK CKE ALL BANKS IDLE ...

Page 12

... Active Command (CS, RAS = LOW, CAS, WE= HIGH) The IS42S16100 includes two banks of 2048 rows each. This command selects one of the two banks according to the A11 pin and activates the row selected by the pins A0 to A10. This command corresponds to the fall of the RAS signal from HIGH to LOW in conventional DRAMs ...

Page 13

... IS42S16100 Self-Refresh Command (CS, RAS, CAS, CKE = LOW HIGH) This command executes the self-refresh operation. The row address to be refreshed, the bank, and the refresh interval are generated automatically internally during this operation. The self-refresh operation is started by dropping the CKE pin from HIGH to LOW. The self-refresh operation continues as long as the CKE pin remains LOW and there is no need for external control of any other pins ...

Page 14

... IS42S16100 COMMAND TRUTH TABLE (1,2) Symbol Command MRS Mode Register Set (3,4) REF Auto-Refresh (5) SREF Self-Refresh (5,6) PRE Precharge Selected Bank PALL Precharge Both Banks ACT Bank Activate (7) WRIT Write WRITA Write With Auto-Precharge READ Read (8) READA Read With Auto-Precharge BST Burst Stop (9) NOP ...

Page 15

... IS42S16100 OPERATION COMMAND TABLE Current State Command Operation Idle DESL No Operation or Power-Down NOP No Operation or Power-Down BST No Operation or Power-Down READ / READA Illegal WRIT/WRITA Illegal ACT Row Active PRE/PALL No Operation REF/SELF Auto-Refresh or Self-Refresh MRS Mode Register Set Row Active DESL No Operation NOP No Operation ...

Page 16

... IS42S16100 OPERATION COMMAND TABLE Current State Command Operation Write With DESL Burst Write Continues, Write Recovery And Precharge Auto-Precharge When Done NOP Burst Write Continues, Write Recovery And Precharge BST Illegal READ/READA Illegal WRIT/WRITA Illegal Illegal (10) ACT Illegal (10) PRE/PALL REF/SELF Illegal ...

Page 17

... This is possible depending on the state of the bank selected by the A11 pin. 11. Time to switch internal busses is required. 12. The IS42S16100 can be switched to power-down mode by dropping the CKE pin LOW when both banks in the idle state. Input pins other than CKE are ignored at this time. ...

Page 18

... IS42S16100 CKE RELATED COMMAND TRUTH TABLE Current State Operation Self-Refresh Undefined Self-Refresh Recovery Self-Refresh Recovery Illegal (2) Illegal (2) Self-Refresh Self-Refresh Recovery Idle State After t Idle State After t Illegal Illegal Power-Down on the Next Cycle Power-Down on the Next Cycle Illegal Illegal Clock Suspend Termination on the Next Cycle ...

Page 19

... IS42S16100 TWO BANKS OPERATION COMMAND TRUTH TABLE Operation CS RAS CAS WE A11 A10 A9-A0 DESL NOP BST READ/READA WRIT/WRITA ACT PRE/PALL REF MRS Notes HIGH level input, L: LOW level input, X: HIGH or LOW level input, RA: Row Address, CA: Column Address 2 ...

Page 20

... IS42S16100 SIMPLIFIED STATE TRANSITION DIAGRAM WRIT CKE_ CKE CLOCK WRITA SUSPEND CKE_ CKE POWER APPLIED Automatic transition following the completion of command execution. Transition due to command input. 20 (One Bank Operation) SREF entry MRS MODE REF IDLE REGISTER SET CKE_ CKE ACT CKE_ ...

Page 21

... The burst length field in the mode register stipulates the number of data items input or output in sequence. In the IS42S16100 product, a burst length full page can be specified. See the table on the next page for details on setting the mode register ...

Page 22

... IS42S16100 MODE REGISTER A11 A10 WRITE MODE LT MODE M11 M10 Note: Other values for these bits are reserved. 22 Address Bus (Ax Mode Register (Mx Burst Length Burst Type Latency Mode 0 Write Mode 0 Burst Read & ...

Page 23

... IS42S16100 BURST LENGTH AND COLUMN ADDRESS SEQUENCE Column Address Burst Length Full Page n n (256) Notes: 1. The burst length in full page mode is 256. Integrated Silicon Solution, Inc. — www.issi.com Rev ...

Page 24

... IS42S16100 BANK SELECT AND PRECHARGE ADDRESS ALLOCATION Row X0 — X1 — X2 — X3 — X4 — X5 — X6 — X7 — X8 — X9 — X10 0 1 Command) X11 0 1 Column Y0 — Y1 — Y2 — Y3 — Y4 — Y5 — Y6 — Y7 — Y8 — Y9 — Y10 0 1 Y11 Row Address Row Address ...

Page 25

... IS42S16100 Burst Read The read cycle is started by executing the read command. The address provided during read command execution is used as the starting address. First, the data corresponding to this address is output in synchronization with the clock signal after the CAS latency period. Next, data corresponding to an address generated automatically by the device is output in synchronization with the clock signal ...

Page 26

... IS42S16100 Read With Auto-Precharge The read with auto-precharge command first executes a burst read operation and then puts the selected bank in the precharged state automatically. After the precharge completes, the bank goes to the idle state. Thus this command performs a read command and a precharge command in a single operation ...

Page 27

... IS42S16100 Write With Auto-Precharge The write with auto-precharge command first executes a burst write operation and then puts the selected bank in the precharged state automatically. After the precharge completes the bank goes to the idle state. Thus this command performs a write command and a precharge command in a single operation ...

Page 28

... IS42S16100 Interval Between Read Command A new command can be executed while a read cycle is in progress, i.e., before that cycle completes. When the second read command is executed, after the CAS latency has elapsed, data corresponding to the new read command is output in place of the data due to the previous read command ...

Page 29

... IS42S16100 Interval Between Write and Read Commands A new read command can be executed while a write cycle is in progress, i.e., before that cycle completes. Data corresponding to the new read command is output after the CAS latency has elapsed from the point the new read command was executed. The I/On pins must be placed in the HIGH impedance state at least one cycle before data is output during this operation ...

Page 30

... IS42S16100 Interval Between Read and Write Commands A read command can be interrupted and a new write command executed while the read cycle is in progress, i.e., before that cycle completes. Data corresponding to the new write command can be input at the point new write command is executed. To prevent collision ...

Page 31

... IS42S16100 Precharge The precharge command sets the bank selected by pin A11 to the precharged state. This command can be executed at a time t following the execution of an active ras command to the same bank. The selected bank goes to the idle state at a time t following the execution of the ...

Page 32

... IS42S16100 Write Cycle Interruption Using the Precharge Command A write cycle can be interrupted by the execution of the precharge command before that cycle completes. The delay time (t ) from the precharge command to the point wdl where burst input is invalid, i.e., the point where input data is no longer written to device internal memory is zero clock cycles regardless of the CAS ...

Page 33

... The IS42S16100 can output data continuously from the burst start address (a) to location a+255 during a read cycle in which the burst length is set to full page. The IS42S16100 repeats the operation starting at the 256th cycle with the data output returning to location (a) and continuing with a+1, a+2, a+3, etc ...

Page 34

... The IS42S16100 can input data continuously from the burst start address (a) to location a+255 during a write cycle in which the burst length is set to full page. The IS42S16100 repeats the operation starting at the 256th cycle with data input returning to location (a) and continuing with a+1, a+2, a+3, etc. A burst stop command must be executed to terminate this cycle ...

Page 35

... CAS latency, as soon as one of the U/LDQM pins goes HIGH, the corresponding externally applied input data will no longer be written to the device internal circuits. Subsequently, the corresponding input continues to be muted as long as that U/LDQM pin remains HIGH. The IS42S16100 will revert to accepting input as soon as CLK COMMAND UDQM ...

Page 36

... CAS latency = 3 Clock Suspend When the CKE pin is dropped from HIGH to LOW during a read or write cycle, the IS42S16100 enters clock suspend mode on the next CLK rising edge. This command reduces the device power dissipation by stopping the device internal clock. Clock suspend mode continues as long as the CKE pin remains low ...

Page 37

... IS42S16100 OPERATION TIMING EXAMPLE Power-On Sequence, Mode Register Set Cycle CLK t CHI HIGH CKE RAS CAS A0- A10 BANK 0 & 1 A11 DQM HIGH DQ WAIT TIME t RP T=100 µs < ...

Page 38

... IS42S16100 Power-Down Mode Cycle CLK t CHI CKS CK CL CKE t CKA RAS CAS A0- A10 BANK 0 & 1 BANK A11 BANK 1 BANK 0 DQM < > PRE < > PALL CAS latency = ...

Page 39

... IS42S16100 Auto-Refresh Cycle CLK t CHI CKS CK CL CKE RAS CAS A0- A10 BANK 0 & 1 A11 DQM < > PALL CAS latency = 2, 3 Integrated Silicon Solution, Inc. — www.issi.com Rev. D 01/28/08 T3 ...

Page 40

... IS42S16100 Self-Refresh Cycle CLK t CHI CKS CK CL CKE t CKA RAS CAS A0- A10 BANK 0 & 1 A11 DQM < > PALL CAS latency = 2, 3 Note 1: A8,A9 = Don’t Care Tm CKS ...

Page 41

... IS42S16100 Read Cycle CLK t CHI CKS CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < > < ACT READ CAS latency = 2, burstlength = 4 Note 1: A8,A9 = Don’ ...

Page 42

... IS42S16100 Read Cycle / Auto-Precharge CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW A10 ROW BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < > < ...

Page 43

... IS42S16100 Read Cycle / Full Page CLK t CHI t t CKS CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 0 A11 DQM DQ t RCD t RAS t RC (BANK 0) < > ...

Page 44

... IS42S16100 Read Cycle / Ping-Pong Operation (Bank Switching CLK t CHI t t CKS CKE t CKA RAS CAS A0-A9 ROW A10 ROW BANK 0 A11 DQM DQ t RRD (BANK ...

Page 45

... IS42S16100 Write Cycle CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 1 BANK 0 DQM DQ t RCD t RAS t RC < > ACT CAS latency = 2, burstlength = 4 Note 1: A8,A9 = Don’ ...

Page 46

... IS42S16100 Write Cycle / Auto-Precharge CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 1 BANK 0 DQM DQ t RCD t RAS t RC < > ACT CAS latency = 2, burstlength = 4 Note 1: A8,A9 = Don’ ...

Page 47

... IS42S16100 Write Cycle / Full Page CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW A10 ROW BANK 0 A11 DQM DQ t RCD t RAS t RC < > ACT 0 CAS latency = 2, burst length = full page Note 1: A8,A9 = Don’ ...

Page 48

... IS42S16100 Write Cycle / Ping-Pong Operation CLK t CHI t t CKS CKE t CKA RAS CAS A0-A9 ROW A10 ROW BANK 0 A11 DQM DQ t RRD (BANK RCD ...

Page 49

... IS42S16100 Read Cycle / Page Mode CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 1 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 50

... IS42S16100 Read Cycle / Page Mode; Data Masking CLK t CHI CKS CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 1 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 51

... IS42S16100 Write Cycle / Page Mode CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 52

... IS42S16100 Write Cycle / Page Mode; Data Masking CLK t CHI t t CKS CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 53

... IS42S16100 Read Cycle / Clock Suspend CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 54

... IS42S16100 Write Cycle / Clock Suspend CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 55

... IS42S16100 Read Cycle / Precharge Termination CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 0 DQM DQ t RCD t RAS t RC < > ACT 0 CAS latency = 2, burst length = 4 Note 1: A8,A9 = Don’ ...

Page 56

... IS42S16100 Write Cycle / Precharge Termination CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK DQM DQ t RCD t RAS t RC < ...

Page 57

... IS42S16100 Read Cycle / Byte Operation CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 1 BANK 0 UDQM LDQM DQ8-15 DQ0-7 t RCD t RAS ...

Page 58

... IS42S16100 Write Cycle / Byte Operation CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 1 BANK 0 UDQM LDQM DQ8-15 DQ0-7 t RCD t RAS ...

Page 59

... IS42S16100 Read Cycle, Write Cycle / Burst Read, Single Write CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW A10 ROW BANK 1 A11 BANK 0 DQM DQ t RCD ...

Page 60

... IS42S16100 Read Cycle CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW A10 ROW BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < > ACT CAS latency = 3, burst length = 4 Note 1: A8,A9 = Don’ ...

Page 61

... IS42S16100 Read Cycle / Auto-Precharge CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW A10 ROW BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 62

... IS42S16100 Read Cycle / Full Page CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 0 A11 DQM DQ t RCD (BANK 0) t RAS ...

Page 63

... IS42S16100 Read Cycle / Ping Pong Operation (Bank Switching CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 0 A11 DQM DQ t RRD (BANK ...

Page 64

... IS42S16100 Write Cycle CLK t CHI t t CKS CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < > ACT CAS latency = 3, burst length = 4 Note 1: A8,A9 = Don’ ...

Page 65

... IS42S16100 Write Cycle / Auto-Precharge CLK t CHI t t CKS CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < > ACT CAS latency = 3, burst length = 4 Note 1: A8,A9 = Don’ ...

Page 66

... IS42S16100 Write Cycle / Full Page CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 0 A11 DQM DQ t RCD t RAS t RC < > ACT 0 CAS latency = 3, burst length = full page Note 1: A8,A9 = Don’ ...

Page 67

... IS42S16100 Write Cycle / Ping-Pong Operation (Bank Switching CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 0 A11 DQM DQ t RRD (BANK ...

Page 68

... IS42S16100 Read Cycle / Page Mode CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 1 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 69

... IS42S16100 Read Cycle / Page Mode; Data Masking CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 1 BANK 0 DQM DQ t RCD t RAS ...

Page 70

... IS42S16100 Write Cycle / Page Mode CLK t CHI t t CKS CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 0 A11 DQM DQ t RCD t RAS t RC < > ACT CAS latency = 3, burst length = 2 Note 1: A8,A9 = Don’ ...

Page 71

... IS42S16100 Write Cycle / Page Mode; Data Masking CLK t CHI t t CKS CKE t CKA RAS CAS A0-A9 ROW ROW A10 t t BANK BANK 1 A11 BANK 0 BANK ...

Page 72

... IS42S16100 Read Cycle / Clock Suspend CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 73

... IS42S16100 Write Cycle / Clock Suspend CLK t CHI CKS CK CL CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 1 A11 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 74

... IS42S16100 Read Cycle / Precharge Termination CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 0 DQM DQ t RCD t RAS t RC < ...

Page 75

... IS42S16100 Write Cycle / Precharge Termination CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 0 DQM DQ t RCD t RAS t RC < > ACT 0 CAS latency = 3, burst length = 4 Note 1: A8,A9 = Don’ ...

Page 76

... IS42S16100 Read Cycle / Byte Operation CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 1 BANK 0 UDQM LDQM DQ8-15 DQ0-7 t RCD t RAS ...

Page 77

... IS42S16100 Write Cycle / Byte Operation CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 A11 BANK 1 BANK 0 UDQM LDQM DQ8-15 DQ0-7 t RCD t RAS ...

Page 78

... IS42S16100 Read Cycle, Write Cycle / Burst Read, Single Write CLK t CHI CKS CL CK CKE t CKA RAS CAS A0-A9 ROW ROW A10 BANK 1 A11 BANK 0 DQM ...

Page 79

... IS42S16100-5BL 6 IS42S16100-6TL IS42S16100-6BL 7 IS42S16100-7TL IS42S16100-7BL Order Part No. 6 IS42S16100-6TLI IS42S16100-6BLI 7 IS42S16100-7TLI IS42S16100-7BLI Package 400-mil TSOP II, Lead-free 60-ball BGA, Lead-free 400-mil TSOP II, Lead-free 60-ball BGA, Lead-free 400-mil TSOP II, Lead-free 60-ball BGA, Lead-free Package 400-mil TSOP II, Lead-free 60-ball BGA, Lead-free 400-mil TSOP II, Lead-free ...

Page 80

... Copyright © 2006 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...

Page 81

... Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — ...