S9S12GN32F0CLF Freescale Semiconductor, S9S12GN32F0CLF Datasheet - Page 384

• Manufacturer Part Number: S9S12GN32F0CLF
• Description: 16-bit Microcontrollers - MCU 16-bit,32k Flash 2k RAM
• Manufacturer: Freescale Semiconductor

Specifications of S9S12GN32F0CLF

• Rohs: yes
• Core: S12
• Processor Series: MC9S12G
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 25 MHz
• Program Memory Size: 32 KB
• Data Ram Size: 1 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 3.13 V to 5.5 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-48
• Mounting Style: SMD/SMT

S12 Clock, Reset and Power Management Unit (S12CPMU)
386
WRTMASK
RSBCK
CR[2:0]
WCOP
Field
2–0
7
6
5
Window COP Mode Bit — When set, a write to the CPMUARMCOP register must occur in the last 25% of the
selected period. A write during the first 75% of the selected period generates a COP reset. As long as all writes
occur during this window, $55 can be written as often as desired. Once $AA is written after the $55, the time-out
logic restarts and the user must wait until the next window before writing to CPMUARMCOP.
the duration of this window for the seven available COP rates.
0 Normal COP operation
1 Window COP operation
COP and RTI Stop in Active BDM Mode Bit
0 Allows the COP and RTI to keep running in Active BDM mode.
1 Stops the COP and RTI counters whenever the part is in Active BDM mode.
Write Mask for WCOP and CR[2:0] Bit — This write-only bit serves as a mask for the WCOP and CR[2:0] bits
while writing the CPMUCOP register. It is intended for BDM writing the RSBCK without changing the content of
WCOP and CR[2:0].
0 Write of WCOP and CR[2:0] has an effect with this write of CPMUCOP
1 Write of WCOP and CR[2:0] has no effect with this write of CPMUCOP.
COP Watchdog Timer Rate Select — These bits select the COP time-out rate (see
Table
counter time-out causes a System Reset. This can be avoided by periodically (before time-out) initializing the
COP counter via the CPMUARMCOP register.
While all of the following four conditions are true the CR[2:0], WCOP bits are ignored and the COP operates at
highest time-out period (
(Does not count for “write once”.)
1) COP is enabled (CR[2:0] is not 000)
2) BDM mode active
3) RSBCK = 0
4) Operation in Special Mode
10-14). Writing a nonzero value to CR[2:0] enables the COP counter and starts the time-out period. A COP
CR2
Table 10-13. COP Watchdog Rates if COPOSCSEL1=0
0
0
0
0
1
1
1
1
Table 10-12. CPMUCOP Field Descriptions
2
MC9S12G Family Reference Manual,
24
CR1
cycles) in normal COP mode (Window COP mode disabled):
0
0
1
1
0
0
1
1
(default out of reset)
CR0
0
1
0
1
0
1
0
1
Description
(COPCLK is either IRCCLK or
OSCCLK depending on the
Cycles to Time-out
COPOSCSEL0 bit)
COP disabled
COPCLK
Rev.1.23
2
2
2
2
2
2
2
14
16
18
20
22
23
24
Table 10-13
Freescale Semiconductor
Table 10-13
and
shows