LM2642MTC/NOPB National Semiconductor, LM2642MTC/NOPB Datasheet
LM2642MTC/NOPB
Specifications of LM2642MTC/NOPB
*LM2642MTC/NOPB
LM2642MTC
Available stocks
Related parts for LM2642MTC/NOPB
LM2642MTC/NOPB Summary of contents
Page 1
... Over-voltage protection is available for both out- puts. A UV-Delay pin is also available to allow delayed shut off time for the IC during an output under-voltage event. Block Diagram © 2006 National Semiconductor Corporation Features n Two synchronous buck regulators n 180˚ out of phase operation n 4.5V to 30V input range n Power good function monitors Ch.1 n 37µ ...
Page 2
Connection Diagram Pin Descriptions KS1 (Pin 1): The positive (+) Kelvin sense for the internal current sense amplifier of Channel 1. Use a separate trace to connect this pin to the current sense point. It should be connected to VIN ...
Page 3
Pin Descriptions (Continued) SW2 (Pin 16): Switch-node connection for Channel 2, which is connected to the source of the top MOSFET of Channel 2. It serves as the negative supply rail for the top-side gate driver, HDRV2. HDRV2 (Pin 17): ...
Page 4
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Voltages from the indicated pins to SGND/PGND: VIN, ILIM1, ILIM2, KS1, KS2 SW1, SW2, RSNS1, RSNS2 FB1, FB2, VDD1, VDD2 PGOOD, COMP1, COMP2, UV ...
Page 5
Electrical Characteristics Unless otherwise specified 15V, GND = PGND = 0V, VLIN5 = VDD1 = VDD2. Limits appearing in boldface type apply IN over the specified operating junction temperature range, (-20˚C to +125˚C, if not otherwise specified). Specifications ...
Page 6
... Note 4: For detailed information on soldering plastic small-outline packages, refer to the Packaging Databook available from National Semiconductor Corporation. Note 5: For testing purposes, ESD was applied using the human-body model, a 100pF capacitor discharged through a 1.5kΩ resistor. ...
Page 7
FIGURE 1. Typical 2 Channel Application Circuit 7 20046203 www.national.com ...
Page 8
FIGURE 2. Typical Single Channel Application Circuit www.national.com 8 20046204 ...
Page 9
9 www.national.com ...
Page 10
Typical Performance Characteristics Softstart Waveforms ( LOAD1 LOAD2 UVP Startup Waveforms Shutdown Waveforms ( LOAD1 LOAD2 www.national.com = 0A) 20046223 20046268 = 0A) 20046222 10 Power On and PGOOD1 Waveforms ( 0A) LOAD1 ...
Page 11
Typical Performance Characteristics Ch.2 Load Transient Response 3.3V , 12V OUT IN Input Supply Current vs Temperature (Shutdown Mode V IN VLIN5 vs Temperature (Continued) 20046229 = 15V) 20046224 20046226 11 Load Transient Response Parallel Operation 1.8V , 12V OUT ...
Page 12
Typical Performance Characteristics FB Reference Voltage vs Temperature Error Amplifier Gain vs Temperature Efficiency vs Load Current Ch.2 = 2.5V, Ch.1 = Off www.national.com (Continued) Operating Frequency vs Temperature 20046266 Efficiency vs Load Current Ch.1 = 5V, Ch.2 = Off ...
Page 13
Operation Descriptions SOFT START The ON/SS1 pin has dual functionality as both channel enable and soft start control. The soft start block diagram is shown in Figure 3. The LM2642 will remain in shutdown mode while both soft start pins ...
Page 14
Operation Descriptions typical) both channels will latch off. Also, UV_DELAY will be disabled and the UV_DELAY pin will return to 0V. During UVP, both the high side and low side FET drivers will be turned off capacitor is ...
Page 15
Operation Descriptions where Imax is the maximum expected load current, including overload multiplier (ie:120%), and Irip is the inductor ripple current (See equation 7). The above equation gives the maximum allowable value for Rsns. Switching losses will increase with Rsns, ...
Page 16
Component Selection Where 200nA is the maximum current drawn by FBx pin. FIGURE 8. Output Voltage Setting Example: Vnom=5V, Vfb=1.238V, Ifbmax=200nA. Choose 60K The output voltage is limited by the maximum duty cycle as well as the minimum on time. ...
Page 17
Output Capacitor Selection (Continued) Notice it is already assumed the total ESR, Re greater than Re_max, otherwise the term under the square root will be a negative value. Also assumed that L has already been selected, ...
Page 18
Input Capacitor Selection Where, again, I1 and I2 are the maximum load currents of channel 1 and 2, and D1 and D2 are the duty cycles. This equation should be used when both duty cycles are ex- pected to be ...
Page 19
Loop Compensation (Continued) FIGURE 10. Control-Output Transfer Function As shown in Figure 10, the control-output transfer function consists of one pole (fp), one zero (fz), and a double pole at fn (half the switching frequency). The following can be done ...
Page 20
Loop Compensation A second zero can also be added with a resistor in series with Cc2. If used, this zero should be placed at fn, where the control to output gain rolls off at -40dB/dec. Generally, fn will be well ...
Page 21
... BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. ...