LTC3890EGN-1#PBF Linear Technology, LTC3890EGN-1#PBF Datasheet - Page 25

• Manufacturer Part Number: LTC3890EGN-1#PBF
• Description: IC BUCK SYNC ADJ 25A DUAL 28SSOP
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LTC3890EGN-1#PBF

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 2
• Voltage - Output: 0.8 ~ 24 V
• Current - Output: 25A
• Frequency - Switching: 50kHz ~ 900kHz
• Voltage - Input: 4 ~ 60 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP
• Primary Input Voltage: 12V
• No. Of Outputs: 2
• Output Voltage: 24V
• Output Current: 25A
• No. Of Pins: 32
• Operating Temperature Range: -40°C To +125°C
• Msl: MSL 1 - Unlimited
• Supply Voltage Min: 4V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -

Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can
be expressed as:
where L1, L2, etc. are the individual losses as a percent-
age of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of
the losses in LTC3890 circuits: 1) IC V
TV
transition losses.
1. The V
2. INTV
APPLICATIONS INFORMATION
CC
%Efficiency = 100% – (L1 + L2 + L3 + ...)
Electrical Characteristics table, which excludes MOSFET
driver and control currents. V
in a small (<0.1%) loss.
control currents. The MOSFET driver current results
from switching the gate capacitance of the power
MOSFETs. Each time a MOSFET gate is switched from
low to high to low again, a packet of charge, dQ, moves
from INTV
out of INTV
control circuit current. In continuous mode, I
= f(Q
the topside and bottom side MOSFETs.
Supplying INTV
through EXTV
the driver and control circuits by a factor of (Duty Cycle)/
(Efficiency). For example, in a 20V to 5V application,
10mA of INTV
of V
10% or more (if the driver was powered directly from
V
IN
regulator current, 3) I
) to only a few percent.
IN
CC
T
IN
current. This reduces the midcurrent loss from
+ Q
current is the sum of the MOSFET driver and
current is the DC supply current given in the
CC
B
), where Q
CC
to ground. The resulting dQ/dt is a current
CC
CC
CC
that is typically much larger than the
current results in approximately 2.5mA
will scale the V
from an output-derived source power
T
and Q
2
R losses, 4) topside MOSFET
IN
B
current typically results
are the gate charges of
IN
current required for
IN
current, 2) IN-
GATECHG
3. I
4. Transition losses apply only to the topside MOSFET(s),
fuse (if used), MOSFET, inductor, current sense resis-
tor and input and output capacitor ESR. In continuous
mode the average output current flows through L and
R
and the synchronous MOSFET. If the two MOSFETs have
approximately the same R
of one MOSFET can simply be summed with the resis-
tances of L, R
example, if each R
= 10mΩ and R
output capacitance losses), then the total resistance
is 130mΩ. This results in losses ranging from 3% to
13% as the output current increases from 1A to 5A for
a 5V output, or a 4% to 20% loss for a 3.3V output.
Efficiency varies as the inverse square of V
same external components and output power level. The
combined effects of increasingly lower output voltages
and higher currents required by high performance digital
systems is not doubling but quadrupling the importance
of loss terms in the switching regulator system!
and become significant only when operating at high
input voltages (typically 15V or greater). Transition
losses can be estimated from:
Other hidden losses such as copper trace and internal
battery resistances can account for an additional 5%
to 10% efficiency degradation in portable systems. It
is very important to include these system level losses
during the design phase. The internal battery and fuse
resistance losses can be minimized by making sure that
C
the switching frequency. A 25W supply will typically
require a minimum of 20μF to 40μF of capacitance
having a maximum of 20mΩ to 50mΩ of ESR. The
LTC3890 2-phase architecture typically halves this input
capacitance requirement over competing solutions.
Other losses including body diode conduction losses
during dead-time and inductor core losses generally
account for less than 2% total additional loss.
2
IN
R losses are predicted from the DC resistances of the
SENSE
Transition Loss = (1.7) • V
has adequate charge storage and very low ESR at
, but is chopped between the topside MOSFET
SENSE
ESR
DS(ON)
= 40mΩ (sum of both input and
and ESR to obtain I
= 30mΩ, R
DS(ON)
IN
• 2 • I
, then the resistance
L
LTC3890
O(MAX)
= 50mΩ, R
2
R losses. For
OUT
• C
25
RSS
for the
SENSE
3890fa
• f