AT91SAM7X256B-CU Atmel, AT91SAM7X256B-CU Datasheet - Page 474

• Manufacturer Part Number: AT91SAM7X256B-CU
• Description: IC MCU 256KB FLASH 100TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X256B-CU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: 91S
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: CAN, Ethernet, SPI, I2S, TWI, USART, USB
• Maximum Clock Frequency: 55 MHz
• Number Of Programmable I/os: 62
• Number Of Timers: 3
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 85 C
• Package: 100TFBGA
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 55 MHz
• On-chip Adc: 8-chx10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

34.6.7
Register Name:
Access Type:
• EP0INT: Endpoint 0 Interrupt Status
• EP1INT: Endpoint 1 Interrupt Status
• EP2INT: Endpoint 2 Interrupt Status
• EP3INT: Endpoint 3 Interrupt Status
• EP4INT: Endpoint 4 Interrupt Status
• EP5INT: Endpoint 5 Interrupt Status
0 = No Endpoint0 Interrupt pending.
1 = Endpoint0 Interrupt has been raised.
Several signals can generate this interrupt. The reason can be found by reading UDP_ CSR0:
EP0INT is a sticky bit. Interrupt remains valid until EP0INT is cleared by writing in the corresponding UDP_ CSR0 bit.
• RXSUSP: UDP Suspend Interrupt Status
0 = No UDP Suspend Interrupt pending.
1 = UDP Suspend Interrupt has been raised.
The USB device sets this bit when it detects no activity for 3ms. The USB device enters Suspend mode.
• RXRSM: UDP Resume Interrupt Status
0 = No UDP Resume Interrupt pending.
1 =UDP Resume Interrupt has been raised.
The USB device sets this bit when a UDP resume signal is detected at its port.
474
RXSETUP set to 1
RX_DATA_BK0 set to 1
RX_DATA_BK1 set to 1
TXCOMP set to 1
STALLSENT set to 1
31
23
15
–
–
–
7
AT91SAM7X512/256/128 Preliminary
UDP Interrupt Status Register
30
22
14
UDP_ ISR
Read-only
–
–
–
6
WAKEUP
EP5INT
29
21
13
–
–
5
ENDBUSRES
EP4INT
28
20
12
–
–
4
SOFINT
EP3INT
27
19
11
–
–
3
EP2INT
26
18
10
–
–
–
2
RXRSM
EP1INT
25
17
–
–
9
1
6120H–ATARM–17-Feb-09
RXSUSP
EP0INT
24
16
–
–
8
0