LPC2387FBD100,551 NXP Semiconductors, LPC2387FBD100,551 Datasheet - Page 28

• Manufacturer Part Number: LPC2387FBD100,551
• Description: IC ARM7 MCU FLASH 512K 100LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2300r

Specifications of LPC2387FBD100,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 100-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 70
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 6x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC23
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN/I2C/I2S/SSP/UART/USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB2387, MCB2387U, MCB2387UME
• Development Tools By Supplier: OM11013
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 6-ch x 10-bit
• On-chip Dac: 1-ch x 10-bit
• Cpu Family: LPC2000
• Device Core: ARM7TDMI-S
• Device Core Size: 16/32Bit
• Frequency (max): 72MHz
• Total Internal Ram Size: 98KB
• # I/os (max): 70
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-4359 - BOARD EVAL FOR LPC2387568-4310 - EVAL BOARD LPC2158 W/LCD568-3999 - BOARD EVAL FOR LPC23 ARM MCU622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 568-4322; 935284932551; LPC2387FBD100-S

NXP Semiconductors
LPC2387
Product data sheet
7.24.1.1 Internal RC oscillator
7.24.1.2 Main oscillator
7.24.1.3 RTC oscillator
7.24.1 Crystal oscillators
7.24.2 PLL
7.24 Clocking and power control
The LPC2387 includes three independent oscillators. These are the Main Oscillator, the
Internal RC oscillator, and the RTC oscillator. Each oscillator can be used for more than
one purpose as required in a particular application. Any of the three clock sources can be
chosen by software to drive the PLL and ultimately the CPU.
Following reset, the LPC2387 will operate from the Internal RC oscillator until switched by
software. This allows systems to operate without any external crystal and the bootloader
code to operate at a known frequency.
The IRC may be used as the clock source for the WDT, and/or as the clock that drives the
PLL and subsequently the CPU. The nominal IRC frequency is 4 MHz. The IRC is
trimmed to 1 % accuracy.
Upon power-up or any chip reset, the LPC2387 uses the IRC as the clock source.
Software may later switch to one of the other available clock sources.
The main oscillator can be used as the clock source for the CPU, with or without using the
PLL. The main oscillator operates at frequencies of 1 MHz to 25 MHz. This frequency can
be boosted to a higher frequency, up to the maximum CPU operating frequency, by the
PLL. The clock selected as the PLL input is PLLCLKIN. The ARM processor clock
frequency is referred to as CCLK elsewhere in this document. The frequencies of
PLLCLKIN and CCLK are the same value unless the PLL is active and connected. The
clock frequency for each peripheral can be selected individually and is referred to as
PCLK. Refer to
The RTC oscillator can be used as the clock source for the RTC and/or the WDT. Also, the
RTC oscillator can be used to drive the PLL and the CPU.
The PLL accepts an input clock frequency in the range of 32 kHz to 25 MHz. The input
frequency is multiplied up to a high frequency, then divided down to provide the actual
clock used by the CPU and the USB block.
•
•
•
•
•
•
Provides Seconds, Minutes, Hours, Day of Month, Month, Year, Day of Week, and
Day of Year.
Dedicated 32 kHz oscillator or programmable prescaler from APB clock.
Dedicated power supply pin can be connected to a battery or to the main 3.3 V.
Periodic interrupts can be generated from increments of any field of the time registers,
and selected fractional second values.
2 kB data SRAM powered by VBAT.
RTC and battery RAM power supply is isolated from the rest of the chip.
All information provided in this document is subject to legal disclaimers.
Section 7.24.2
Rev. 4 — 10 February 2011
for additional information.
Single-chip 16-bit/32-bit MCU
LPC2387
© NXP B.V. 2011. All rights reserved.
28 of 64