C8051F413-GM Silicon Laboratories Inc, C8051F413-GM Datasheet - Page 70

• Manufacturer Part Number: C8051F413-GM
• Description: IC 8051 MCU 16K FLASH 28QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F41xr

Specifications of C8051F413-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-QFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 20
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.25 V
• Data Converters: A/D 20x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F4x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 20
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F410DK
• Minimum Operating Temperature: - 40 C
• On-chip Dac: 2-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1454 - ADAPTER PROGRAM TOOLSTICK F411336-1317 - KIT EVAL FOR C8051F411336-1314 - KIT DEV FOR C8051F41X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1311

C8051F410/1/2/3
6.1.2. Update Output Based on Timer Overflow
The IDAC output update can be scheduled on a Timer overflow. This feature is useful in systems where the
IDAC is used to generate a waveform of a defined sampling rate, by eliminating the effects of variable
interrupt latency and instruction execution on the timing of the IDAC output. When the IDAnCM bits
(IDAnCN.[6:4]) are set to ‘000’, ‘001’, ‘010’ or ‘011’, writes to both IDAC data registers (IDAnL and IDAnH)
are held until an associated Timer overflow event (Timer 0, Timer 1, Timer 2 or Timer 3, respectively)
occurs, at which time the IDAnH:IDAnL contents are copied to the IDAC input latch, allowing the IDAC out-
put to change to the new value. When updates are scheduled based on Timer 2 or 3, updates occur on
low-byte overflows if Timer 2 or 3 is in 8-bit mode and high-byte overflows if Timer 2 or 3 is in 16-bit mode.
6.1.3. Update Output Based on CNVSTR Edge
The IDAC output can also be configured to update on a rising edge, falling edge, or both edges of the
external CNVSTR signal. When the IDAnCM bits (IDAnCN.[6:4]) are set to ‘100’, ‘101’, or ‘110’, writes to
the IDAC data registers (IDAnL and IDAnH) are held until an edge occurs on the CNVSTR input pin. The
particular setting of the IDAnCM bits determines whether the IDAC output is updated on rising, falling, or
both edges of CNVSTR. When a corresponding edge occurs, the IDAnH:IDAnL contents are copied to the
IDAC input latch, allowing the IDAC output to change to the new value.
6.2.
The IDAC data word can be Left Justified or Right Justified as shown in Figure 6.2. When Left Justified, the
8 MSBs of the data word (D11-D4) are mapped to bits 7-0 of the IDAnH register and the 4 LSBs of the data
word (D3-D0) are mapped to bits 7-4 of the IDAnL register. When Right Justified, the 4 MSBs of the data
word (D11-D8) are mapped to bits 3-0 of the IDAnH register and the 8 LSBs of the data word (D7-D0) are
mapped to bits 7-0 of the IDAnL register. The IDAC data word justification is selected using the IDAnRJST
bit (IDAnCN.2).
The full-scale output current of the IDAC is selected using the IDAnOMD bits (IDAnCN[1:0]). By default,
the IDAC is set to a full-scale output current of 2 mA. The IDAnOMD bits can also be configured to provide
full-scale output currents of 0.25 mA, 0.5 mA, or 1 mA.
70
Left Justified Data (IDAnRJST = 0):
Right Justified Data (IDAnRJST = 1):
IDAn Data Word
D11
(D11–D0)
IDAC Output Mapping
0xFFF
0x000
0x001
0x800
D10
D9
2048/4096 x 2 mA 2048/4096 x 1 mA 2048/4096 x 0.5 mA 2048/4096 x 0.25 mA
4095/4096 x 2 mA 4095/4096 x 1 mA 4095/4096 x 0.5 mA 4095/4096 x 0.25 mA
D8
1/4096 x 2 mA
IDAnH
IDAnH
‘11’ (2 mA)
0 mA
Figure 6.2. IDAC Data Word Mapping
D11
D7
D10
D6
Output Current vs IDAnOMD bit setting
D5
D9
1/4096 x 1 mA
‘10’ (1 mA)
0 mA
D4
D8
Rev. 1.1
D3
D7
D2
D6
1/4096 x 0.5 mA
‘01’ (0.5 mA)
D1
D5
0 mA
D0
D4
IDAnL
IDAnL
D3
1/4096 x 0.25 mA
‘00’ (0.25 mA)
D2
0 mA
D1
D0