P89LPC931FDH,112 NXP Semiconductors, P89LPC931FDH,112 Datasheet - Page 35

• Manufacturer Part Number: P89LPC931FDH,112
• Description: IC 80C51 MCU FLASH 8K 28-TSSOP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC931FDH,112

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 12MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LED, POR, PWM, WDT
• Number Of I /o: 26
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-TSSOP
• Processor Series: P89LPC9x
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 45 C
• For Use With: 622-1014 - BOARD FOR LPC9XX TSSOP622-1008 - BOARD FOR LPC9103 10-HVSON622-1006 - SOCKET ADAPTER BOARDMCB900K - BOARD PROTOTYPE NXP 89LPC9EPM900K - EMULATOR/PROGRAMMER NXP P89LPC9568-4000 - DEMO BOARD SPI/I2C TO DUAL UART568-3510 - DEMO BOARD SPI/I2C TO UART622-1002 - USB IN-CIRCUIT PROG LPC9XX568-1759 - EMULATOR DEBUGGER/PROGRMMR LPC9X568-1758 - BOARD EVAL FOR LPC93X MCU FAMILY
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-1284-5; 935273877112; P89LPC931FDH; P89LPC931FDH,129; P89LPC931FDH-S

Philips Semiconductors
9397 750 14472
Product data
Fig 13. Comparator input and output connections.
(P0.5) CMPREF
(P0.4) CIN1A
(P0.3) CIN1B
(P0.2) CIN2A
(P0.1) CIN2B
V REF
8.20.1 Internal reference voltage
8.20 Analog comparators
Two analog comparators are provided on the P89LPC930/931. Input and output
options allow use of the comparators in a number of different configurations.
Comparator operation is such that the output is a logic 1 (which may be read in a
register and/or routed to a pin) when the positive input (one of two selectable pins) is
greater than the negative input (selectable from a pin or an internal reference
voltage). Otherwise the output is a ‘0’. Each comparator may be configured to cause
an interrupt when the output value changes.
The overall connections to both comparators are shown in
comparators function to V
When each comparator is first enabled, the comparator output and interrupt flag are
not guaranteed to be stable for 10 microseconds. The corresponding comparator
interrupt should not be enabled during that time, and the comparator interrupt flag
must be cleared before the interrupt is enabled in order to prevent an immediate
interrupt service.
When a comparator is disabled the comparator’s output, COx, goes HIGH. If the
comparator output was LOW and then is disabled, the resulting transition of the
comparator output from a LOW to HIGH state will set the comparator flag, CMFx.
This will cause an interrupt if the comparator interrupt is enabled. The user should
therefore disable the comparator interrupt prior to disabling the comparator.
Additionally, the user should clear the comparator flag, CMFx, after disabling the
comparator.
An internal reference voltage generator may supply a default reference when a single
comparator input pin is used. The value of the internal reference voltage, referred to
as V
REF
, is 1.23 V 10%.
CN1
CN2
CP1
CP2
Rev. 05 — 15 December 2004
Comparator 1
Comparator 2
DD
CO1
CO2
= 2.4 V.
Change Detect
Change Detect
8-bit microcontrollers with two-clock 80C51 core
OE1
OE2
CMF1
CMF2
P89LPC930/931
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
CMP1 (P0.6)
CMP2 (P0.0)
Figure
EC
002aaa422
13. The
Interrupt
35 of 55