MC56F8002VWL Freescale Semiconductor, MC56F8002VWL Datasheet - Page 18

• Manufacturer Part Number: MC56F8002VWL
• Description: DSC 12K FLASH 32MHZ 28-SOIC
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8002VWL

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 12KB (6K x 16)
• Program Memory Type: FLASH
• Ram Size: 1K x 16
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 15x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 28-SOIC
• Product: DSCs
• Data Bus Width: 16 bit
• Processor Series: MC56F80xx
• Core: 56800E
• Instruction Set Architecture: Dual Harvard
• Device Million Instructions Per Second: 32 MIPs
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 40
• Data Ram Size: 2 KB
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: MC56F8006DEMO, APMOTOR56F8000E
• Interface Type: LIN, I2C, SCI, SPI
• Minimum Operating Temperature: - 40 C
• For Use With: APMOTOR56F8000E - KIT DEMO MOTOR CTRL SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Signal/Connection Descriptions
EXT_SYNC)
18
(FAULT1)
(FAULT2/
GPIOA3
(PWM3)
(EXTAL)
GPIOA4
(PWM4)
GPIOA5
(PWM5)
Signal
(TIN2)
(TIN3)
Name
(TXD)
(SDA)
SOIC
28
17
16
14
LQFP
Table 5. 56F8006/56F8002 Signal and Package Information (continued)
32
24
22
20
LQFP
48
36
33
29
MC56F8006/MC56F8002 Digital Signal Controller, Rev. 3
Input/Open
Output
Output
Output
Analog
Output
Output
Output
Output
Output
Output
Input/
Input/
-drain
Input/
Input/
Type
Input
Input
Input
Input
enabled
enabled
enabled
internal
internal
internal
During
Reset
pullup
pullup
pullup
Input,
Input,
Input,
State
Port A GPIO — This GPIO pin can be individually programmed as
an input or output pin.
PWM3 — The PWM channel 3.
TXD — The SCI transmit data output or transmit/receive in single
wire operation.
EXTAL — External Crystal Oscillator Input. This input can be
connected to a 32.768 kHz or 1–16 MHz external crystal or ceramic
resonator. When used to supply a source to the internal PLL, the
crystal/resonator must be in the 4 MHz to 8 MHz range. Tie this pin
low or configure as GPIO if XTAL is being driven by an external
clock source.
If using a 32.768 kHz crystal, place the crystal as close as possible
to device pins to speed startup.
After reset, the default state is GPIOA3.
Port A GPIO — This GPIO pin can be individually programmed as
an input or output pin.
PWM4 — The PWM channel 4.
SDA — The I
FAULT1 — PWM fault input 1used for disabling selected PWM
outputs in cases where fault conditions originate off-chip.
TIN2 — Dual timer module channel 2 input
After reset, the default state is GPIOA4.
Port A GPIO — This GPIO pin can be individually programmed as
an input or output pin.
PWM5 — The PWM channel 5.
FAULT2 — PWM fault input 2 used for disabling selected PWM
outputs in cases where fault conditions originate off-chip.
EXT_SYNC — When not being used as a fault input, this pin can be
used to receive a pulse to reset the PWM counter or to generate a
positive pulse at the start of every PWM cycle.
TIN3 — Dual timer module channel 3 input
After reset, the default state is GPIOA5.
2
C serial data line.
Signal Description
Freescale Semiconductor