AT90PWM1-16MU Atmel, AT90PWM1-16MU Datasheet - Page 37

• Manufacturer Part Number: AT90PWM1-16MU
• Description: IC AVR PWM 8KB FLASH 16MHZ 32QFN
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM1-16MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 19
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8. Power Management and Sleep Modes
8.0.1
4378C–AVR–09/08
Sleep Mode Control Register – SMCR
Sleep modes enable the application to shut down unused modules in the MCU, thereby saving
power. The AVR provides various sleep modes allowing the user to tailor the power consump-
tion to the application’s requirements.
To enter any of the five sleep modes, the SE bit in SMCR must be written to logic one and a
SLEEP instruction must be executed. The SM2, SM1, and SM0 bits in the SMCR Register select
which sleep mode (Idle, ADC Noise Reduction, Power-down, Power-save, or Standby) will be
activated by the SLEEP instruction. See
while the MCU is in a sleep mode, the MCU wakes up. The MCU is then halted for four cycles in
addition to the start-up time, executes the interrupt routine, and resumes execution from the
instruction following SLEEP. The contents of the register file and SRAM are unaltered when the
device wakes up from sleep. If a reset occurs during sleep mode, the MCU wakes up and exe-
cutes from the Reset Vector.
Figure 7-1 on page 27
tion. The figure is helpful in selecting an appropriate sleep mode.
The Sleep Mode Control Register contains control bits for power management.
• Bits 3..1 – SM2..0: Sleep Mode Select Bits 2, 1, and 0
These bits select between the five available sleep modes as shown in
Table 3. Sleep Mode Select
Note:
• Bit 1 – SE: Sleep Enable
The SE bit must be written to logic one to make the MCU enter the sleep mode when the SLEEP
instruction is executed. To avoid the MCU entering the sleep mode unless it is the programmer’s
purpose, it is recommended to write the Sleep Enable (SE) bit to one just before the execution of
the SLEEP instruction and to clear it immediately after waking up.
Bit
Read/Write
Initial Value
SM2
0
0
0
0
1
1
1
1
1. Standby mode is only recommended for use with external crystals or resonators.
R
7
–
0
SM1
presents the different clock systems in the AT90PWM1, and their distribu-
0
0
1
1
0
0
1
1
R
6
–
0
R
5
–
0
SM0
0
1
0
1
0
1
0
1
Table 3
R
4
–
0
Sleep Mode
Idle
ADC Noise Reduction
Power-down
Reserved
Reserved
Reserved
Standby
Reserved
for a summary. If an enabled interrupt occurs
SM2
R/W
3
0
(1)
SM1
R/W
2
0
SM0
R/W
Table
1
0
AT90PWM1
3.
R/W
SE
0
0
SMCR
37