ATTINY25-15MZ Atmel, ATTINY25-15MZ Datasheet - Page 124

• Manufacturer Part Number: ATTINY25-15MZ
• Description: MCU AVR 2K FLASH 15MHZ 20-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY25-15MZ

• Package / Case: 20-QFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 6
• Eeprom Size: 128 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Program Memory Size: 2KB (2K x 8)
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: UART, SPI, USI
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Data Rom Size: 128 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 4
• Height: 0.75 mm
• Length: 4 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 4 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

18.7.6
124
ATtiny25/45/85
ADC Control and Status Register A – ADCSRA
• Bits 3:0 – MUX3:0: Analog Channel and Gain Selection Bits
The value of these bits selects which combination of analog inputs are connected to the ADC. In
case of differential input (ADC0 - ADC1 or ADC2 - ADC3), gain selection is also made with these
bits. Selecting ADC2 or ADC0 as both inputs to the differential gain stage enables offset mea-
surements. Selecting the single-ended channel ADC4 enables the temperature sensor. Refer to
Table 18-4
effect until this conversion is complete (ADIF in ADCSRA is set).
Table 18-4.
1.
2.
• Bit 7 – ADEN: ADC Enable
Writing this bit to one enables the ADC. By writing it to zero, the ADC is turned off. Turning the
ADC off while a conversion is in progress, will terminate this conversion.
• Bit 6 – ADSC: ADC Start Conversion
In Single Conversion mode, write this bit to one to start each conversion. In Free Running mode,
write this bit to one to start the first conversion.
Bit
Read/Write
Initial Value
MUX3..0
0101
0000
0001
0010
0011
0100
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
For offset calibration only .
For Temperature Sensor
(1)
for details. If these bits are changed during a conversion, the change will not go into
ADEN
R/W
Input Channel Selections
7
0
ADSC
Single Ended
R/W
ADC0 (PB5)
ADC1 (PB2)
ADC2 (PB4)
ADC3 (PB3)
6
0
1.1V/2.56V
ADC4
Input
N/A
N/A
0V
ADATE
R/W
(2)
5
0
See “Operation” on page 112.
ADIF
R/W
4
0
Differential Input
ADC2 (PB3)
ADC2 (PB3)
ADC2 (PB3)
ADC2 (PB3)
ADC0 (PB5)
ADC0 (PB5)
ADC0 (PB5)
ADC0 (PB5)
Positive
ADIE
R/W
3
0
ADPS2
R/W
2
0
Differential Input
ADC2 (PB3)
ADC2 (PB3)
ADC3 (PB4)
ADC3 (PB4)
ADC0 (PB5)
ADC0 (PB5)
ADC1 (PB2)
ADC1 (PB2)
ADPS1
R/W
Negative
1
0
N/A
N/A
ADPS0
R/W
0
0
ADCSRA
7598H–AVR–07/09
Gain
20x
20x
20x
20x
1x
1x
1x
1x